0
Any electrical supplier should be able to get that for you. Check you local Yellow Pages for electrical suppliers.
<<>>
A GDP 200 is an older type breaker that was manufactured by General Switch. It had a 10KAIC (interruption capacity). This type of distribution panel was used 40 to 50 years ago. The main breaker is almost next to non existent. The main breakers were manufactured by a different company and General Switch used them in their panels. You might look on EBay under electrical breakers. The original branch circuit breakers are also hard to find but some different brands will fit. There are some sites on the net that refurbish old breakers for your type of scenario. Safety wise it is not a good idea to mix and match breakers. You might want to consider budgeting for a distribution panel change.
What else can I help you with?
What is type of breaker for 41 amp's?
For a 41 amp load, you would typically use a 50 amp circuit breaker. The general rule is to select a breaker size that is 125% of the continuous load amps or equal to the load amps if it is not a continuous load. In this case, 41 amps is considered a continuous load, so you would round up to the nearest available breaker size, which is 50 amps.
How do you wire a 100 amp breaker box and a 100 amp safety switch right from the power meter?
To wire a 100 amp breaker box and safety switch from the power meter, you will need to connect the hot wire from the meter to the main breaker in the breaker box. From there, you will connect the individual circuits to the breakers. The safety switch should be connected after the breaker box to provide an additional level of protection. It's crucial to follow all local building codes and regulations when performing electrical work.
Can you install a tandem breaker?
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
How does drawable circuit breaker look like?
A drawable circuit breaker is a graphical representation of a circuit breaker that can be visually manipulated. It typically consists of a switch that can be opened or closed to interrupt or restore the flow of electricity. This type of circuit breaker is often used in educational settings to help students understand how circuit breakers work.
What does qp mean on a breaker?
"QP" on a breaker typically indicates that it is a type of breaker manufactured by Siemens. It is part of the product code for Siemens breakers and does not specifically denote any particular function or feature.
What is a reusable safety switch that breaks the circuit when the current gets too high?
In the electrical trade, this device is known as a circuit breaker.
What causes an electrical surging sounds be when home ac unit is running?
The wiring to the unit is either not on the right type of breaker switch or the unit is not hooked up directly to the breaker box at all.
How can I safely add a breaker to a panel in my electrical system?
To safely add a breaker to your electrical panel, first turn off the main power switch. Then, carefully remove the panel cover and identify a suitable location for the new breaker. Make sure to use the correct size and type of breaker for your system. Connect the new breaker to the panel following the manufacturer's instructions, ensuring all connections are secure. Finally, replace the panel cover and turn the main power switch back on to test the new breaker.
What type panel does a 4 pole breaker require?
The panel and breaker have to be of the same manufacturer. This way the breaker will fit into the panel. If the panel has a push in bus bar, the breaker must also be the type to accept the bus bar. If the bus bars in the panel are of the bolt in type then the breaker also has to be a bolt in breaker.
What is circuit breaker and its type?
A circuit breaker(s) is what you will find inside your electrical box in your house the idea behind them is when a room in your house draws too many Amps the circuit breaker will turn off all the power to that room to re-engage them you simply switch it back on. There are many types of circuit breakers with different rattings like 15A or 100A, this tells you at what point they will 'break' the circuit and turn off the power.
Where to find engin management switch?
There is not an `Engine Management`switch There are computers and add on devices that can allow that type of adjustment, but it will not be a single switch
What is the recommended type of breaker to use for a hot tub that requires a 50 amp GFCI breaker for safety?
The recommended type of breaker to use for a hot tub that requires a 50 amp GFCI breaker for safety is a 50 amp GFCI breaker.
How can I identify the type of a circuit breaker?
To identify the type of a circuit breaker, look for the markings on the breaker itself. Common types include thermal-magnetic, magnetic-only, and ground fault circuit interrupters (GFCI). These markings will indicate the type of protection the breaker provides.
What is type of breaker for 41 amp's?
For a 41 amp load, you would typically use a 50 amp circuit breaker. The general rule is to select a breaker size that is 125% of the continuous load amps or equal to the load amps if it is not a continuous load. In this case, 41 amps is considered a continuous load, so you would round up to the nearest available breaker size, which is 50 amps.
Where is main breaker switch?
a circuit breaker trips on overload,if this breaker has tripped many times it may be worn out,if there is a overload happening the breaker is doing it s job keeping you safe.Main breaker needs to be replaced when your meter has been pulled(removed from metersocket)Have a electrician look at it and verify problem, you should not attempt to change out yourself it will be live.......
What is the recommended type of GFCI 50 amp breaker for outdoor electrical installations?
The recommended type of GFCI 50 amp breaker for outdoor electrical installations is a weather-resistant GFCI breaker.
How do you wire a 100 amp breaker box and a 100 amp safety switch right from the power meter?
To wire a 100 amp breaker box and safety switch from the power meter, you will need to connect the hot wire from the meter to the main breaker in the breaker box. From there, you will connect the individual circuits to the breakers. The safety switch should be connected after the breaker box to provide an additional level of protection. It's crucial to follow all local building codes and regulations when performing electrical work.
