Wiki User
∙ 11y agoBecause it makes the quotient in divisable by multiple cation
IN KID WORDS
It makes number bigger to add or divide the dividend or the number on the side go into it so always out 000ss!
HOPE THIS HELPED,
Kelsey
Wiki User
∙ 11y agoAdding a zero to the right of the decimal point in the quotient ensures that the division process is carried out accurately and consistently, maintaining the correct place value alignment. This step helps avoid potential errors in decimal division calculations.
Because a percent can be turned into a decimal like a fraction can be .That is wrong it is if you move the decimal point two places to the right you'll turn a decimal to a percent.Yours is half way through.
You move six decimal places
A pint is half of a quart, so in decimal form, a pint is equivalent to 0.5 quarts.
To order decimals from smallest to largest, start by comparing the digits to the left of the decimal point. If they are the same, move to the first digit to the right. Continue this process until you can determine the order of the decimals. Remember, the decimal point separates the whole number from the fractional part, with smaller numbers appearing to the left of larger numbers.
There is no smallest decimal - just as there is no largest number. If x was said to be the smallest decimal, inserting a zero immediately after the decimal point would give a number equal to a tenth of x - ie smaller than x.
significant figures. you'll learn how to use significant figures in high school chemistry.
Because when you want to divide a decimal by a larger number, like 3 divided by 5, you need to add a zero to make the 3, 30, so you can divide, but then the quotient has to be a decimal because 5 does not go into 3 evenly
If it's long division then it is because the quotient will become a decimal number after its decimal point
Divide as normal, but make sure to place the decimal point in the quotient directly above the decimal point in the dividend.
Put the decimal point for the quotient exactly above the decimal point in the dividend. Then forget about it, and just keep your digits lined up as you do the division. The decimal point winds up exactly where it belongs in the quotient.
The decimal point moves to the left.
There are two possible reasons. One is to indicate a degree of precision in the calculation. The other is so that the quotient is expressed with the conventional number of digits after the decimal point. For example, most currencies use 100 minor units per major unit and so monetary value are given to two decimal places. Thus GBP3 for 2 items would be shown as a unit price of GBP1.50 rather than GBP1.5
No. The part of the number after the decimal point (if any) is the quotient of the remainder from the original division and the original denominator.
Estimating will give an indication of the order of magnitude of the answer. The decimal point determines the order of magnitude.
The decimal point moves 3 places to the right.
The point moves further to the left.
The decimal point goes in the quotient the moment you reach the decimal point in the dividend and need to use the digit in the tenths column. When using the "Bus stop" method, the digits will line up so that the decimal point goes in the quotient directly above the decimal point in the dividend.Using the Bus stop method, it is easiest to put the decimal point in the quotient above the decimal point in the dividend first (before any any division calculation is done) and then do the division by ignoring the decimal points and putting digits in the quotient as normal; except if once all the digits of the dividend have been used there is a non-zero remainder, zeros can be added to the end of the dividend as they are trailing zeros after a decimal point which make no difference to the number.eg dividing 1.2 by 5:First place the decimal point in the quotient over the decimal point in the dividend:_____.___------5_|_1.2Now divide as normal:____0.2__------5_|_1.2____1 0____----______2Used up all the digits of the dividend but have a remainder, so add trailing zeros after the decimal point and finish the division:____0.24__--------5_|_1.2000____1 0____----______20______20______---_______0Only needed one extra 0, but it did not hurt putting three of them.→ 1.2 ÷ 5 = 0.24Sometimes the decimal may recur or not terminate; in that case, stop when the required level of accuracy is reached (rounding by calculating a further digit and using that as the deciding digit).