answersLogoWhite

0

Yes, some can work in other panels. But you go to an electrical supplier and get the one

that is the brand of the panel. If it is old and you can't find it, then try a GE breaker.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Natural Sciences

What breaker can I use if I dont have a westinghouse breaker?

If you don't have a Westinghouse breaker, you should use a breaker that is compatible with your electrical panel. Consult the panel's specifications or a qualified electrician to determine the appropriate replacement breaker for your specific panel. Using an incompatible breaker can be dangerous and may violate electrical codes.


Will a square d circuit breaker fit in Allen bradley panel?

No, the Square D designed breaker can only be installed in a Square D manufactured panel.


Is it a Code violation to modify a breaker to make it fit in a panel?

Yes, modifying a breaker to fit in a panel is typically a code violation. Breakers are designed to specific dimensions and altering them can pose safety hazards, such as improper fit and overheating. It is recommended to always use breakers that are compatible with the panel and have been tested and approved by a recognized testing laboratory.


Can you mix challenger breakers with other brand breakers?

The critical element is if they match the connectors in the electric panel and you use the correct amperage breaker for the wiring of the circuit. Connectors to the electric panel must match exactly because you don't want to force the replacement breaker or have it not fit when the panel cover is reinstalled. ---- The above stated matters to an extent but not really the issue. It is much deeper to the extent that if not UL rated for that panel or a direct replacement via corporate buy out over the years it can become A. an issue and fail inspection B. a hazard well beyond amp rating of the breaker or "fitting correctly when panel cover reinstalled" C. without being UL rated or an acceptable replacement it can become an insurance issue, that could fall on homeowner or inspector or whomever last worked inside the panel. I just grazed the surface. Some breakers are well made, some manufacturers deceive even to get UL rating when in fact they tested improperly etc... Yes some breakers can replace challenger breakers. Often falling in line with which company bought out challenger or the rights. Read tag on load center to find out what breaker types are acceptable. Then proceed to search which manufacturers make breakers that are acceptable within that panel. wash. rinse. repeat. keep digging.


What would happen if a 200 amp breaker is used in a 100 amp sub panel?

There are two things to think about here. First of all a 200 amp breaker will not physically fit into a 100 amp panel. This is so designed because the panel buss is not designed to conduct 200 amps before the current is cut off. A 100 amp rating on the panel is the maximum amount of current that the manufacturer states, that can be handled safely. Second if the 200 amp breaker is in the main panel then everything downstream from that breaker has to be rated for 200 amp conductivity. The wire size will have to be 3/0 from the breaker to the first over current device in the sub panel which will be the sub panel's main breaker. The sub panel can not be a load center but will have to be a combination panel. I doubt that the 100 amp sub panel's main breaker lugs would be large enough to connect the 3/0 cable.

Related Questions

What are the different options available for breaker panel blanks?

Breaker panel blanks are available in various sizes and configurations to fit different types of breaker panels. Common options include single-pole blanks, double-pole blanks, and combination blanks that can accommodate different types of breakers. It is important to choose the correct size and type of blank to ensure proper fit and safety in the breaker panel.


What type panel does a 4 pole breaker require?

The panel and breaker have to be of the same manufacturer. This way the breaker will fit into the panel. If the panel has a push in bus bar, the breaker must also be the type to accept the bus bar. If the bus bars in the panel are of the bolt in type then the breaker also has to be a bolt in breaker.


Will cutler hammer breaker panel fit a GE breaker?

No, a Cutler Hammer will not work in a GE panel or vice versa.


What breaker can I use if I dont have a westinghouse breaker?

If you don't have a Westinghouse breaker, you should use a breaker that is compatible with your electrical panel. Consult the panel's specifications or a qualified electrician to determine the appropriate replacement breaker for your specific panel. Using an incompatible breaker can be dangerous and may violate electrical codes.


Will a GE breaker fit a cutler hammer panel?

No, a Cutler Hammer will not work in a GE panel or vice versa.


Can you use a Murray breaker in a Bryant panel?

No, they will not fit. You can use Westinghouse, Cutler Hammer BR series, and Connecticut Electrical UBITBC series breaker. All of those will fit.


Do circuit breaker blanks have to fit completely in the breaker panel?

Yes, the code requires a complete dead front so that no access can be made to the bare distribution bus behind the panel face.


Will a square d circuit breaker fit in Allen bradley panel?

No, the Square D designed breaker can only be installed in a Square D manufactured panel.


Will a General Electric breaker fit a Cutler Hammer panel?

A General Electric (GE) breaker is generally not compatible with a Cutler-Hammer panel, as each manufacturer designs their breakers to fit only their specific panels due to differing configurations and standards. Installing a breaker that is not designed for a particular panel can pose safety risks and may violate electrical codes. Always consult the panel's documentation or a qualified electrician to ensure compatibility when replacing or installing breakers.


Do they make a 30-40 amp two pole breaker compatible with a square d breaker?

No, if you have a Square D distribution panel only Square D breakers will fit in it.


Is it a Code violation to modify a breaker to make it fit in a panel?

Yes, modifying a breaker to fit in a panel is typically a code violation. Breakers are designed to specific dimensions and altering them can pose safety hazards, such as improper fit and overheating. It is recommended to always use breakers that are compatible with the panel and have been tested and approved by a recognized testing laboratory.


Can you mix challenger breakers with other brand breakers?

The critical element is if they match the connectors in the electric panel and you use the correct amperage breaker for the wiring of the circuit. Connectors to the electric panel must match exactly because you don't want to force the replacement breaker or have it not fit when the panel cover is reinstalled. ---- The above stated matters to an extent but not really the issue. It is much deeper to the extent that if not UL rated for that panel or a direct replacement via corporate buy out over the years it can become A. an issue and fail inspection B. a hazard well beyond amp rating of the breaker or "fitting correctly when panel cover reinstalled" C. without being UL rated or an acceptable replacement it can become an insurance issue, that could fall on homeowner or inspector or whomever last worked inside the panel. I just grazed the surface. Some breakers are well made, some manufacturers deceive even to get UL rating when in fact they tested improperly etc... Yes some breakers can replace challenger breakers. Often falling in line with which company bought out challenger or the rights. Read tag on load center to find out what breaker types are acceptable. Then proceed to search which manufacturers make breakers that are acceptable within that panel. wash. rinse. repeat. keep digging.