0
You tripped a circuit breaker while trying to install a dimmer switch and now all the power to my condo is out. You reset all the breakers including the main and the power won't come on.?
Wiki User
∙ 14y ago
If resetting the main circuit breaker did not restore power, it could indicate a larger electrical issue. It is recommended to contact a licensed electrician to inspect the electrical panel and address any potential issues to restore power safely. Avoid attempting any further DIY fixes that could pose a risk of injury or damage.
Add your answer:
Earn +20 pts
Can you put in piggy back circuit breakers in a circuit panel?
The electrical terminology for this type of breaker is a tandem breaker. It is where two breakers circuits can be in the same one breaker slot in a distribution panel. On this type of breaker there will be two output for a circuit value of what ever the breaker is rated for.
Can you install a tandem breaker?
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
Does temperature affect circuit breakers?
Temperature can affect circuit breakers, as extreme temperatures can impact their performance. Low temperatures can cause the breaker to become stiff and less responsive, while high temperatures can lead to overheating and failure. It is important to install circuit breakers in environments where the temperature range is within their specified operating limits to ensure proper functioning.
Can you install a 2 20 breaker into a breaker box that has space but all other breakers add up to more amps than the 200 amp main breaker?
No, you cannot install a 2x20 amp breaker if the total amperage of all the breakers exceeds the main breaker rating, as this would overload the system. The total amperage of the breakers should not exceed the main breaker rating to ensure safe operation of the electrical system.
Can you install 2 conducters in a cuttler hammer 1 pole 20 amp breaker?
No, Cutler Hammer 1-pole breakers are designed to accommodate only one conductor per terminal. It is not recommended to install multiple conductors on a single terminal as it can lead to overheating and potential safety hazards. If you need to connect multiple conductors, you should consider using a different type of breaker or a junction box.
How would you install ge circuit breakers?
There are many ways one can install ge circuit breakers. One can install ge circuit breakers by turning off the power supply, removing the panel cover, testing it for power, and installing it by alining the breaker with the unused panel space.
Can you install a tandem breaker?
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
Can an AC circuit breakers be used on a DC circuit and will this give that circuit adequate protection?
Check the nameplate on the actual breaker. Some breakers are rated for AC or DC. If it doesn't specifically list DC on the nameplate, then no, you should not rely on the breaker to adequately protect the circuit.
What is a difference between 10KA and 22KA circuit breakers?
The previous answer is incorrect, and I would advise that user to not give out information if they are going to give completely misguided information. The interrupting rating of a breaker is the maximum current that the breaker is designed to handle, at the breaker's rated voltage, before damage will occur to the breaker. A breaker will trip at FAR LESS than the interrupting rating, but it is extremely dangerous to expose the breaker to any situation where it will have more than the rated interruption current. the breaker is designed for. The reason some breakers are rated at 22kA instead of 10kA is because they typically have far larger conductors hooked up to them, so with the lowered impedance on the circuit there is more of a chance for the breaker to experience a higher fault current at the breaker. So electricians install 22kA breakers to handle the higher "available fault current."
Can you install a 2 20 breaker into a breaker box that has space but all other breakers add up to more amps than the 200 amp main breaker?
No, you cannot install a 2x20 amp breaker if the total amperage of all the breakers exceeds the main breaker rating, as this would overload the system. The total amperage of the breakers should not exceed the main breaker rating to ensure safe operation of the electrical system.
Can you install 2 conducters in a cuttler hammer 1 pole 20 amp breaker?
No, Cutler Hammer 1-pole breakers are designed to accommodate only one conductor per terminal. It is not recommended to install multiple conductors on a single terminal as it can lead to overheating and potential safety hazards. If you need to connect multiple conductors, you should consider using a different type of breaker or a junction box.
How do you install a miniature breaker?
A miniature breaker is just two breaker that fit into one breaker slot. These types of breakers are designed to install the same as a full size breaker. Different types of breakers have different mounting configurations to the panels bus bars so installation instructions are not possible without knowing the make and type.
What is a sentence with the words circuit breaker in it?
Example sentence - We hired an electrician to at the circuit breaker and install an updated panel.
Can you use two 15 amp single pole breakers in place of a double pole 30 amp breaker?
No, you cannot use two separate 15 amp single pole breakers in place of a double pole 30 amp breaker. A double pole breaker is designed to simultaneously disconnect both circuit conductors, whereas using two single pole breakers would not provide the necessary protection for the circuit. It is important to use the correct size and type of breaker as specified by the electrical code for safety and functionality.
What do I do if there is no circuit breaker for outdoor light?
If you have a light that is not being powered through a circuit breaker or fuse, you should call a qualified electrician to remove this circuit from the panel's bus and install a circuit breaker for it. Without an overcurrent protective device (circuit breaker or fuse) you have a potential fire hazard.
In science to prevent overloading in a parallel circuit you could install a what?
you can use a fuse or circuit breaker
What circuit breakers will interchange with ITE EQ-T?
Siemens QP and Murray MP circuit breakers will interchange with ITE EQ-T circuit breakers as they are all compatible. However, it is always recommended to refer to the manufacturer's specifications to ensure compatibility and safety.
