0
Add your answer:
Earn +20 pts
What 1 and 4 out of 5 equal to?
It is equal to 1.8It is equal to 1.8It is equal to 1.8It is equal to 1.8
Why isn't a parallelogram a regular polygon?
Angles are not necessarily equal, and sides are not necessarily equal in length.Angles are not necessarily equal, and sides are not necessarily equal in length.Angles are not necessarily equal, and sides are not necessarily equal in length.Angles are not necessarily equal, and sides are not necessarily equal in length.
Is 5.20 greater than 5.2?
It is the same. So they are equal
What is equal to 428?
428 is equal to 428. No other number is equal to 428.
Is 200 l equal to 2 kl is equal to?
no its equal to 2000 l
Can a DC 9v 100MA device use 9v 650MA adaptor?
sure, no problem! The power supplying device is rated as to its MAXIMUM current delivering capacity, so 100ma being less than 650ma, you could run up to 6 of those devices in parallel with that adapter. You should not try to run a 650ma device with a 100ma supply though.
A series circuit has 100mA flowing through a 1.5kohm load What is the power dissipated by the load?
A series circuit has 100mA flowing through a 1.5kohm load. The power dissipated by the load is equivalent to 15 Watt. This is based on the formula, power is equals to square current times load.
How long can it be expected to supply a current of 100mA if a cell supplies a load current of .5 amperes for a period of 20 hours?
100 hours.
Can a 9 volt 100mA ac adapter be substituted for a 9 volt DC 300mA adapter?
No. an AC adapter will not work for equipment that needs DC.
Can a 6volt 600 milliamps adopter be substituted for a 6 volts 100 milliamps adopter?
Yes, you can substitute a 6V 600mA adapter for a 6V 100mA adapter. The important thing is to match the voltage (6V) while ensuring the new adapter can supply at least the same current (milliamps) as the original, to avoid damaging the device or causing underperformance. In this case, the 600mA adapter has a higher current capacity, which is safe to use with a device that previously used a 100mA adapter.
Can I use a battery charger that is rated at 6V DC 1000 mA to replace one that was 6V DC 100mA or will this damage the battery?
No you should not do that. It will damage the battery and the battery will explode.
Is it ok to use an adaptor with 4.5V 100mA output which works for an Omron BP measurement machine which needs 6.0 V 500mA output?
No. Both the voltage and the current are too low.
Can you use 9v 100ma adaptor for powering a leap pad instead o 9v 700ma?
No, if the device needs 700mA of current, your power adapter cannot supply adequate current.
There is a total of 500mA of current into five parallel resisters the currents through four of the resistors are 50mA 150mA25mA and 25mAand 100mA what is the current through the fifth resister?
150 mA is.
Eska 5hp outboard motor need to know what year it is and what fuel mixture to put in it found 2 numbers on it T-642-01A and 5516059 help please?
model 1165 eska,what fuel mix?
What does 100ma mean on an ac dc adaptor?
100 ma is equal to .1 amp. It is the capacity or the maximum amount of current that can be drawn from the adapter that is established by the manufacturer of the adapter. If more that the nameplate rating is drawn from the adapter it will start to heat up and if this overload is left on for a extended period of time the adapter will be destroyed because of the heat build up. The insulation on the windings breaks down under heat and eventually will short out making the adapter useless.
How do you figure the coefficient variable with mR readings of 210 235 221 212 and 208 100mA point 1sec and 80kVp the answer is point 0469?
It looks like you answered your own copy-and-pasted question.
