0
Add your answer:
Earn +20 pts
In a hydraulic device the surface area of the small piston is 20cm and the surface area of the piston is 80cm to lift a 400 N barrel placed on the large piston you must apply a force of?
796.2 N/m^2
How do you find the pupulation density of an area?
-- Find out the population of the area. -- Find out the area of the area. -- Divide the population by the area. The result is the population density of the area.
Calculate the force output by the larger piston of a hydraulic lift when a force of 700 n is exerted on the smaller piston the areas of the two pistons are 20 cm squared and 950 cm squared?
Well, isn't that just a happy little problem to solve! To calculate the force output, you can use the formula: Force output = (Area of larger piston / Area of smaller piston) x Force input. So, in this case, it would be (950 cm² / 20 cm²) x 700 N. Just remember, there are no mistakes, only happy little accidents in math!
If a master cylinder with a two-square-inch piston travels 1/2 inch how far would the wheel cylinder with one -square-inch piston be moved?
-1
How do you find the surface area of an octagonal pyramid?
The formula to find the area of an octagonal pyramid is area of base plus area of sides.
How do you find area of piston?
radius squared x 3.14 = area diameter squared x 3.14 / 4 = area
How do you get the area of a piston?
To get the area of a piston, you need to measure the diameter or radius of the piston head and use the formula for the area of a circle (A = πr^2) where r is the radius of the piston head. Once you have the radius, plug it into the formula to calculate the area of the piston head.
What best describes the piston surface area of a single rod double acting piston?
The piston surface area of a single-rod, double-acting piston consists of two main areas: the face area on one side of the piston and the annular area on the opposite side. The face area is the circular area of the piston that directly pushes against the fluid, while the annular area is the ring-shaped area around the piston rod that is also exposed to the fluid pressure. By summing these two areas, you can determine the total surface area of the piston that is subjected to the fluid pressure.
If the area of piston 1 is half the area of piston 2 does it require half the newtons of force to lift an object?
No, the force required to lift an object is not directly proportional to the area of the piston. If the area of piston 1 is half the area of piston 2, it would not require half the force to lift an object. Force is dependent on pressure, which is equal to force divided by area.
What is the fluid pressure on piston 2?
The fluid pressure on piston 2 is equal to the force applied on piston 2 divided by the area of piston 2. It can be calculated using the formula: pressure = force / area.
If the output piston is a car hoist was replaced by a piston of twice the area what would happen to the output force?
If the output piston of a car hoist is replaced by a piston of twice the area, the output force would double. This is because the force exerted by a hydraulic system is directly proportional to the area of the piston. Since the new piston has twice the area, it would exert twice the force on the car lift.
What is the force exerted on the right piston?
The force exerted on the right piston is equal to the pressure of the fluid multiplied by the area of the piston. This is calculated using the equation: Force = Pressure x Area.
If a Master Cylinder piston applies pressure to a brake piston that has twice as much square area what will be the Force from the second piston?
Twice as much
Explain how the difference in the area of two different sized pistons can have a dramatic effect on the forces applied to each piston?
The force applied on a piston is directly proportional to the pressure acting on it, which in turn depends on the area of the piston. If the two pistons have different areas, the larger piston will generate a greater force for the same pressure compared to the smaller piston due to the differences in surface area. This can lead to significant differences in the forces experienced by each piston.
In a hydraulic system piston 1 has a surface area of 100 cm2 and piston 2 has a surface area of 900 cm2. Piston 1 exerts a pressure of 10 Pa on the fluid in the hydraulic lift. What is the fluid press?
Using the equation for hydraulic systems (F1/A1 = F2/A2), where F1 is the force of piston 1, A1 is its surface area, F2 is the force of piston 2, and A2 is its surface area, we can calculate the force of piston 2 as 90 N. Since pressure (P) is defined as force per unit area (P = F/A), the pressure exerted by piston 2 on the fluid is 0.1 Pa.
In a hydraulic device the surface area of the small piston is 20cm and the surface area of the piston is 80cm to lift a 400 N barrel placed on the large piston you must apply a force of?
796.2 N/m^2
What is total effective piston area?
Total effective piston area is the combined area of all the pistons in an engine that are responsible for producing power during the combustion process. It is calculated by adding up the cross-sectional area of each piston that is exposed to the combustion chamber. This measurement is important for determining the engine's displacement and power output.
