0
How many 50 inch hoses can be made from hose reels containing 486 inch and 514 inch of hose?
Wiki User
∙ 10y ago
9 and 10 respectively. Both have remainders but you may not be able to use it to make a new one
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
A two inch hose carries two times the volume of a one inch hose.?
All else being equal, a 2-inch hose carries 4 times the volume as a 1-inch hose.
Weight of 50 ft section of 3 inch fire hose?
Weight of 50ft section of 3 inch hose with water in it?
What is the volume of 50 feet of 2.5 inch hose?
50 feet of 2.5-inch diameter hose has a volume of: 1.7 cubic feet (12.72 liquid gallons)
How many gallons of water in a 2.5 inch hose 100 feet long?
There need not be any water at all in the hose! The capacity of the hose is 3.41 cubic feet.
How much water can a 50 ft section of 3 inch hose hold in gallons?
A water hose is a cylinder, and since the volume of a cylinder is pi*r^2*height, we can calculate the volume of the water hose by finding the radius and height. A 3 inch hose has a radius of 1.5 inches, and 50 ft is equal to 600 inches, so 1.5^2 is 2.25, and 2.25*600 is 1,350. Finally we multiply by Pi to get approximately 4,239 cubic inches. Since 1 cubic inch is equal to 0.00432 gallons, there are 18.3506 gallons.
What is the diameter of the radiator hoses on Ford model A?
Top hose is 2 inch I.D. Two lower hoses are 1 3/4 I.D.
How long is a standard air compressor hose?
A standard air compressor hose is on average about 25 to 50 feet in length. These hoses are typically 1/4 of an inch in width but sometimes 1/2 inch too.
Where is the heater hose on a Cadillac Eldorado?
There are two hoses going to the heater core. Passenger side of the firewall in the engine compartment. Two 3/4 inch hoses about 3 inches apart.
What the size of the vacuum hose on 89 Honda Accord?
There are several different sizes of vacuum hoses in the 89 Accord. The hoses are at various places in the engine bay and under the dash, and sizes can range from 1/4 inch to 3/4 inch diameters.
How do you flush a heater core on a 99 ford escort?
The heater core is on the back side of the firewall. It has 2 hoses of 1/2 inch diameter running into it. It is about in the center of the firewall. Take the 2 hoses off the firewall. Get a hose with good pressure and back flush the heater core by running the hose into the side with the long hose on it. If you are not sure which side to do then do it both ways.
A two inch hose carries two times the volume of a one inch hose.?
All else being equal, a 2-inch hose carries 4 times the volume as a 1-inch hose.
Where is the PCV valve located on a 1994 Ford Escort 1.9l?
It is between 2 hoses about `1/2 inch wide. The top hose comes from the valve cover and the bottom hose comes from the air cleaner housing. It is where these 2 hoses come together in front of the radiator that the PCV is located. The elbow connecting the top hose has been known to crack. Check it first.
What is used to connect the heater core hoses together when bypassing it?
Use a 1 to 2-inch piece of pipe that will fit inside the heater hoses and clamp with hose clamps. You nay need to put a little grease or vaseline in the inside tip of the hoses so you can slide them on over the pipe.
What is the longest water hose available for home gardening?
The longest water hose available for Home Gardening is the Flexogen Hose. The Flexogen Hose comes in 1/2 to 1 inch in diameter. It has lengths up to 250 feet long and has 500 psi burst strength.
How do you bypass the heater in a 1996 blazer?
Remove the heater hoses from the heater core at the firewall and hook them together. In order to connect to two same diameter hoses together, get a 5 or 6 inch piece of pipe which is the same diameter as the heater core tubes from which the hoses were removed. Install the pipe halfway into one hose and secure tightly with a worm-drive hose clamp. Then once secure, do the same with the other hose.j3h.
How do you bypass the heater core on a 1995 Ford Thunderbird?
U cut both hoses & connect together with a piece of half inch conduit.OR put plugs in each hose & secure with hose clamps-(same as above)--OR get 2 block-off caps & install on the heater hose nipples.
Why it is not getting heat?
Use an air hose to blow through the 3/4 inch rubber hoses going to the heater core. Mine was full of crap. Took three minutes to fix it.
