answersLogoWhite

0


Best Answer

A percentage means "out of 100", but it is not unit-specific. This means that 1 percent is the same as 1/100 centimetres, 1/100 inches, 1/100 litres, 1/100 years etc... It is a proportion, not a measurement as such. To clarify, the slope is 1/100 inches. (i.e per every 100 inches you go forwards, you go down 1 inch).

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is 1 percent slope in inches?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is 1.5 percent slope in inches?

1-13/16"


How many inches per foot in a 2 percent slope?

how many inches per foot is a 2% slope


What percent grade is a 3 to 1 slope?

It is a 300% slope!


How do i know how many inches i need to drop IN one linear foot to gain a four percent slope?

Since one foot is 12 inches a four percent slope is .04X12 = 0.48 inch drop


What is a 1 in 14 slope?

A 1 in 14 slope is where when the height raises 1 inch from the slope it is equal to the road 14 inches up the hill.


What is the slope of a ramp that has a rise of 1 inch over a run of 10ft?

Slope is equal to rise over run. There are 12 inches in a foot, so 10 feet is actually 120 inches. Therefore, the slope is equal to 1/120.


How convert percent grade to slope?

how to convert slope into percent grade


How do you convert .25 inch per foot into degrees or percent slope?

To convert .25 inch per foot into degrees or percent slope, you first need to determine the rise over the run. In this case, .25 inch per foot is equivalent to a rise of .25 inches for every 12 inches of horizontal distance (1 foot). To convert this into degrees, you can use the arctangent function: arctan(.25/12) ≈ 1.19 degrees. To convert this into percent slope, you can use the formula: percent slope = (rise / run) x 100. In this case, it would be (.25/12) x 100 ≈ 2.08% slope.


How to determine paver pitch?

place a 4 foot level on the sloped surface. Use a small wedge like a door stop on the downhill side of the level about 1 inch back from the end. Raise that end until the bubble is centered and shows level. Measure the distance from the ground to the bottom of the level. If it were to be one inch that would be 1 in 48 inches or about 2.1 inches in 100 inches or about a 2 percent slope. A metric level of 100 cm (1m) would give you the percent slope without calculation.


What percent is 9 inches of 1 foot?

Since 9 out of 12 equals 75 percent, then 9 inches out of 12 inches (a foot) is 75 percent.


What is the slope of the percent error envelope lines bounding y equals x?

I get ((2/(error_fraction+1))-1) and ((2/(1-error_fraction))-1) is this right? I think that the slope is 45 degrees 45 degrees is the angle of the corner that is made between the line y=x and the horizontal axis. In algerbraic terminology the slope is defined as "m" in the formula y=mx+b... In the y = x scenario the slope is "1". The question I proposed was, what is the slope of the percent error envelope lines and the equations I proposed were for y=mx where m is a function of the percent error from the y=x line. So a 20 percent error would have an upper error envelope slope of...


How do carpenters and architects express roof slope?

It is most often expressed as a ratio of inches of rise per 12 inches of run. A roof slope that rises 4 inches for every 12 inches of run is a "4 in 12" slope, or 4/12 slope, or 4:12 slope.