answersLogoWhite

0

What else can I help you with?

Continue Learning about Other Math

What is the take out for a 4 inch 90 degree elbow?

6 inch or 4 inch if it's a short radius


What is take off measurement for 90 degree 8 inch pipe?

The take-off for a standard radius 90 is one and one half the diameter of the pipe. Example: 6 inch 90 has a take- off of 9 inches. The take-off for short radius 90 would be the dia. of the pipe. Long radius 90 is 2 times the pipe diameter.


How big is one inch in diameter?

A US 25 cent piece, a quarter, is close to one inch in diameter; it is just short. Its diameter is just about 15/16 of an inch. The diameter of a circle is the length all the way across the face of the circle going straight through the center. So a quarter gives you a good estimate of a circle with one inch diameter. Just imagine a circle very slightly bigger across.If you take an ordinary lead pencil and trace a circle using a US quarter as your template, you'll probably come even closer to a one inch diameter circle. Test it out with a ruler handy so you can get a better sense of it.


How many sand grains is in a cubic ft?

It depends on grain size, which can be as small as 0.004 inch or as big as 0.1 inch. If we take an average grain size of 0.02 inch diameter that is 0.00000043 cubic inch volume and a cubic foot is 1728 cubic inches then (not considering packing voids) that is 1728/.000000 = 4 billion grains!


How many hydrogen atoms would it take to equal one inch?

A hydrogen atom has a diameter of approx 10.6 nanometres = 0.000000417 inches. So it would require around 2.4 million hydrogen atoms.

Related Questions

What is the take off for a 4 inch 90 degree elbow?

The take-off for a 4-inch 90-degree elbow is typically calculated based on the diameter of the pipe and the angle of the bend. For a 4-inch diameter pipe, the take-off is generally around 10 to 12 inches. This measurement may vary slightly depending on the specific design and manufacturer of the elbow, so it's always best to refer to the manufacturer's specifications for precise dimensions.


What is the take out for a 4 long radius degree weld ell?

The take-out for a 4-inch long radius degree weld elbow (or ell) is typically determined by the radius of the elbow and the pipe diameter. For a long radius elbow, the centerline radius is usually 1.5 times the pipe diameter; therefore, for a 4-inch diameter pipe, the centerline radius would be 6 inches. The take-out length is generally the distance from the end of the pipe to the point where the elbow connects, which can be calculated based on the elbow's radius and the angle of the bend. For a 90-degree elbow, the take-out would be approximately equal to the radius plus the straight length of the pipe before and after the elbow, typically resulting in about 9 to 10 inches.


What is the take off for a 26 inch 90 degree elbow?

39in.


What is the take off for a half inch screwed 90 degree elbow?

1/2 inch


What is the take out of a 6 inch short radius 90 degree elbow?

4 1/2 inch


What is the take out for a 4 inch 90 degree elbow?

6 inch or 4 inch if it's a short radius


What is the take out for an 8 LR 90 degree elbow?

7/8 of an inch


What is the take off for a 8 butt weld elbow?

The take-off for an 8-inch butt weld elbow typically refers to the length of pipe that is required to accommodate the elbow's angle and diameter when calculating pipe runs. For a standard 90-degree elbow, the take-off is generally about 8 inches plus the radius of the elbow, which is typically 10 inches for an 8-inch elbow, resulting in a total take-off of approximately 18 inches. For other angles (like 45 degrees), the take-off measurements would differ accordingly. Always consult specific piping codes or standards for precise measurements.


What is the formula to find take off for 30degree elbow?

The take-off for a 30-degree elbow can be calculated using the formula: Take-off = Pipe Diameter × 0.577. For example, if the pipe diameter is 4 inches, the take-off would be 4 × 0.577 = 2.308 inches. This formula helps determine the horizontal run of the pipe after the elbow joint.


How do you calculate a 45 degree elbow take off?

To calculate a 45-degree elbow takeoff, you need to consider the diameter of the pipe and the flow rate. Typically, you can use the formula for an elbow fitting's pressure loss, which is based on the flow velocity and the elbow's characteristics. Additionally, you may need to refer to manufacturer data or standards that provide specific loss coefficients for a 45-degree elbow to ensure accurate pressure drop calculations in your system.


What is the take out of a 6 inches socket weld 90 degree elbow?

what is the take out of 6 inches pipe of a socket weld 90 degree elbow


What is the take out of 6 inches socket weld 90 degree elbow?

what is the take out of 6 inches pipe of a socket weld 90 degree elbow