0
The take off measurement for a 90-degree 8-inch pipe refers to the distance from the center of the pipe to the point where the pipe makes a 90-degree turn. To calculate this measurement, you would typically use a combination of trigonometry and pipe fitting standards. The exact calculation would depend on the specific type of pipe fitting being used and the angle of the turn.
12
12
12
Add your answer:
Earn +20 pts
What is the take out for a 4 inch 90 degree elbow?
6 inch or 4 inch if it's a short radius
What is the take off of a 90 degree elbow with 1 inch diameter?
2 inches
What is one fourth in one inch?
unit of measurement. Look at ruler and take an inch and divide by 4 equal parts. Each has a mark, one of those is 1/4 (quarter) 2 a half (1/2), 3 is 3/4 and 4 makes 1 whole inch. Just like a quarter (money) is one fourth of a dollar (whole)
How many ten inch squares would it take to make a 108 inch by 102 inch quilt?
110 of them.
How do you divide 1 inch into 3 parts?
Take a inch and divide it into 3parts
What is the take off measurement of 45 degree elbow 18 inches pipe?
11 1/4
Take off of an eight inch pipe with a 45 degree angle?
this app help you: "Miter Flat Pattern Design" in play.google.com
What is the take off measurements for 22.5 degree pipe fittings?
what size and style? If it is butt weld you half the pipe size 3 times and take the 2nd and 4th number and add together. 6 inch example below....1] 6"2] 3" add this3] 1 1/2"4] 3/4" and this................so 6 inch 45 would be 3 3/4"you also can use this formula.. pipe size times 0.625 [ 5/8 ]
What is the take off formula off 45 degree elbow pipe?
The take off formula of a 45 degree elbow pipe, will depend on what the pipe is on. Sometimes a 45 degree pipe will need a 90 degree right angle turn to come off.
What an 8 inch 90 degree pipe fitting take off when rolled 45 degrees?
Well, honey, when you roll an 8-inch 90-degree pipe fitting 45 degrees, you're looking at a take off of about 8 inches. It's simple geometry, darling. Just remember, always measure twice and cut once - ain't nobody got time for mistakes in the world of piping!
What is the take off for a six inch pipe?
Three inches
How many one inch pipe equals for one four inch pipe for water distribution?
It would take sixteen one-inch pipes to equal the cross-sectional area of one four-inch pipe. This assumes the pipes are circular in cross-section.
What is the take off for an 8-inch pipe?
4 5/16
What is the pipe formula for the take off of a tee?
The same as a short radius 90 of that same pipe size. I Rule of thumb, for example: 1/2 inch copper tubing you would take off 1/2 inch, likewise 3/4 tubing take 3/4 inch. Your question is 'pipe' are you actually using pipe, cutting and threading pipe? I am often asked questions and find that people are not using 'pipe'. Copper tubing, pvc, cpvc, dwv are quite forgiving when it comes to a slight miscut. Iron and galvanized piping is a different story, get it right the first time!
For pipefitters what is the take off on a 6 inch short radius 90 degree ell?
Short Radius 90 degree elbows are the same as pipe size.... Long Radius 90's are pipe size times 1.5.... so a 6" (SR) elbow is 6"... a 6" (LR) elbow would be 9"
What is the take off for a half inch screwed 90 degree elbow?
1/2 inch
I need to know the take off for a one inch butt weld ninety. is it one and a half time the size of the pipe.?
1.5in For a 90 degree butt-joint each piece must be cut at 45 degrees. So it will be one inch measured along the length of the pipe or 1.414 inches measured along the 45 degree cut. When you look at the cut face at right angles (90 degrees) you will see an ellipse that is 1 inch wide and 1.414 inches long.
