0
switches work by interupting the hot side of a wire loop, so what you do is you wire your non hot (usually black) wires directly to the device you are trying to control, next, to one side of the switch you connect your two reds, then to the other side of the switch connet the hot lead from your device.
What else can I help you with?
How do you wire an additional light to another light with a switch?
In the wall switch box you should have a white and black pair from your source of power (120 volts). The other pair of black and white wires from the wall box should be going to the light fixture junction box. With the power off, connect the two white wires together with a wire nut. Connect the two bare copper ground wires together making sure that at least one of the ground wires goes under the green screw in the switch junction box. Turn the switch to the off position, no little indicator bump showing on the switch toggle lever. Now take the black incoming hot wire and put it under the top screw on the switch. Hot wires always go to the top of switches. Now put the black wire that is going to the light fixture under the bottom screw. Tighten both. Install the switch into the wall box with the switch handle in the down position. All switches when installed must be off in the down position. Install the switch plate cover.
How do you wire a light switch?
The information you need needs a wiring diagram!The Related Links have diagrams and the answers to the Related Questions shown below should also be of some help to you.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How do you wire a 3-way dimmer switch that has two red wires and one black and one green when the box has two red and two black?
you can only have one dimmer, the other switch needs to be not a dimmer. the green wire is ground, it connects to a bare copper wire found in the box, or to the box itself, if the box is metal. the black wire is"common" it either connects to the wire found in the box that has power in it or to the black wire that goes to the light. the 2 red wires are"travelers" they connect to the wires found in the box that go from switch to switch. if you don't know how to check which wire does what( continuity), it is possible to keep changinging the connections until the switch works. you will want to do this with a conventional switch, and install the dimmer afer you identify what wires are travelers and wich are common. you will destroy a dimmer switch by searching for the right connection. once you have identified the common wires, it will be on the black screw of a 3way switch; you can put that wire on the black wire of the dimmer. one red goes on one traveler, the other on another traveler. there might be a white wire in the box, if it is connected to other white wires and not to the switch, leave it alone. if a single white wire is connected to old switch, it may be a traveler.you will connect a red dimmer wire to this. opening the other switch location will show you if the white wire is used as a traveler.the black wire has to be either power coming in, or the wire going to the light. the reds are just connecting the 2 switches.
How do you wire a tri-light bulb table lamp with 3 wire rotary switch?
If the tri-light needs a new lamp holder try any reputable lighting house store. These types of retailers have all of the parts that you need to repair any lamp configurations. The new switch will have a rotary switch built into it just like the lamp had when it was new. There are only two wires to connect to it. Don't disconnect the old one until you have the new one and just put the wires on the same terminals as the they are wires on the old switch.
New ceiling fixture goes on as soon as power is back even though switch is off?
You switched the power and switch wires. There should be two sets of wires in the ceiling box. 2 black, 2 white, 2 bare. Two groups of three. The white wire going to the light is the incoming wire. The black one in that group is the power coming in. Take that black wire and connect it to the other black wire. The second black wire goes to the switch. The power comes back to the light on the white wire of that set. Connect that white wire to the black wire in the fixture. The switch should work now. That is if everyone wired the house the way it is supposed to be.
How do you wire up a light switch?
To wire up a light switch, you need to turn off the power, remove the old switch, connect the wires to the new switch (usually black to black, white to white, and ground to ground), and then secure the switch in place. Finally, turn the power back on to test the switch.
How do you properly wire a single light switch?
To properly wire a single light switch, you need to turn off the power, remove the old switch, connect the wires to the new switch (usually black to black, white to white, and ground to ground), and then secure the switch in place before turning the power back on.
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
How can I connect a light switch?
To connect a light switch, first turn off the power to the circuit at the breaker box. Then, remove the old switch by unscrewing the cover plate and disconnecting the wires. Next, connect the wires to the new switch by matching the colors and tightening the screws. Finally, screw the switch back into place, replace the cover plate, and turn the power back on to test the switch.
How do you wire a light switch in a home electrical system?
To wire a light switch in a home electrical system, you need to turn off the power, remove the old switch, connect the wires to the new switch (usually black to black, white to white, and ground to ground), and then secure the switch in place before turning the power back on.
How can I properly install and connect electrical switch wiring in my home?
To properly install and connect electrical switch wiring in your home, follow these steps: Turn off the power to the circuit at the breaker box. Remove the existing switch and disconnect the wires. Connect the new switch by matching the wire colors (black to black, white to white, green or bare copper to ground). Secure the wires with wire nuts and screw the switch into place. Turn the power back on and test the switch to ensure it is working properly. Remember to always follow safety precautions and consult a professional if you are unsure.
What is the correct single pole light switch wiring diagram for installing a new light switch in a residential setting?
To install a single pole light switch in a residential setting, connect the black wire from the power source to the brass screw terminal on the switch, and connect the black wire from the light fixture to the other brass screw terminal. Connect the white wires together with a wire nut, and connect the ground wire to the green screw terminal on the switch. Make sure to turn off the power before starting the installation.
How do I properly install and connect wall switch wiring in my home?
To properly install and connect wall switch wiring in your home, first turn off the power to the circuit at the breaker box. Remove the old switch and disconnect the wires. Connect the new switch by matching the wires to the corresponding terminals (usually labeled). Secure the switch in place and carefully tuck the wires back into the electrical box. Turn the power back on and test the switch to ensure it is working correctly.
How do you wire an additional light to another light with a switch?
In the wall switch box you should have a white and black pair from your source of power (120 volts). The other pair of black and white wires from the wall box should be going to the light fixture junction box. With the power off, connect the two white wires together with a wire nut. Connect the two bare copper ground wires together making sure that at least one of the ground wires goes under the green screw in the switch junction box. Turn the switch to the off position, no little indicator bump showing on the switch toggle lever. Now take the black incoming hot wire and put it under the top screw on the switch. Hot wires always go to the top of switches. Now put the black wire that is going to the light fixture under the bottom screw. Tighten both. Install the switch into the wall box with the switch handle in the down position. All switches when installed must be off in the down position. Install the switch plate cover.
How do you replace a neutral safety switch in a 1998 Nissan sentra?
its screwed into your transmission,loosen both wires and unscrew part and screw new one in and connect wires.
How to change a light switch with 2 wires?
To change a light switch with 2 wires, first turn off the power to the switch at the circuit breaker. Remove the cover plate and unscrew the switch from the wall. Disconnect the two wires from the old switch and connect them to the new switch, making sure to match the wire colors. Screw the new switch back into place, replace the cover plate, and turn the power back on at the circuit breaker.
How can I install a new light switch in my home?
To install a new light switch in your home, first turn off the power to the circuit at the breaker box. Remove the existing switch cover plate and switch. Connect the wires from the new switch to the corresponding wires in the wall using wire nuts. Secure the switch in place and replace the cover plate. Turn the power back on and test the new switch to ensure it is working properly.
