0
What else can I help you with?
Is 30 amp double pole breaker ok for 4800 watt wall heater?
Yes, a 30 amp double pole breaker would be suitable for a 4800 watt wall heater. Since watts equals volts multiplied by amps, this wall heater on a 240-volt circuit would draw 20 amps (4800 watts/240 volts), which is less than the 30 amp capacity of the breaker.
What size breaker do i need for a 220w wall ac?
For a 220W wall air conditioner, you typically need a circuit breaker rated for at least 15 to 20 amps, depending on the manufacturer’s specifications. Since the AC unit will draw about 1 amp at 220 volts (220W/220V = 1A), a 15-amp breaker is usually sufficient. However, it’s essential to check the specific requirements of your unit and local electrical codes to ensure safety and compliance. Consider also having a licensed electrician evaluate your setup if you're unsure.
How do you install ATMOR instant water heater?
To install an ATMOR instant water heater, first shut off the water supply and electric power. Mount the unit securely on a wall using the provided hardware. Connect the water pipes and electrical wires according to the manufacturer's instructions. Test the unit for proper operation before use.
How do i convert my charmglow nataurel gas heater to propane gas?
Converting a natural gas heater to propane gas usually involves changing the orifice size and adjusting the gas pressure. It's important to consult the manufacturer's instructions or hire a professional to ensure the conversion is done safely and properly. Using the wrong type of gas can be dangerous and damage the heater.
Is it safe to paint an in-wall electric heater vent in a apartment?
Yes heater vents can be painted the same colour as your walls.
How do I turn off a baseboard heater when there is no visible thermostat?
There is a thermostat somewhere, usually on the wall or on the heater itself. Just turn the breaker off at the breaker box. Label the breaker if it is not already labeled. Once the power is turned off to the unit, you can disconnect the wires inside the heater to permanantly shut down the unit.
What best breaker rating for 1.5 hp air-con unit?
The breaker you use is determined by the size of the wire in the wall not by what is being connected to that circuit. If you have 14/2 wire then use a 15 amp breaker. If you have 12/2 wire then use a 20 amp breaker. The breaker protects the wiring not the item connected.
How do you fit a baseboard heater?
they generaly have a thermostat mounted on the unit or on the wall.
Is 30 amp double pole breaker ok for 4800 watt wall heater?
Yes, a 30 amp double pole breaker would be suitable for a 4800 watt wall heater. Since watts equals volts multiplied by amps, this wall heater on a 240-volt circuit would draw 20 amps (4800 watts/240 volts), which is less than the 30 amp capacity of the breaker.
How can I turn on a wall heater?
To turn on a wall heater, locate the power switch or dial on the unit and set it to the desired temperature. Wait a few moments for the heater to start producing heat. Make sure the area around the heater is clear and not obstructed.
What best breaker rating for 1.5 hp air con unit?
The breaker you use is determined by the size of the wire in the wall not by what is being connected to that circuit. If you have 14/2 wire then use a 15 amp breaker. If you have 12/2 wire then use a 20 amp breaker. The breaker protects the wiring not the item connected.
How can I effectively remove a baseboard heater from a room?
To effectively remove a baseboard heater from a room, first turn off the power to the heater at the circuit breaker. Then, remove the cover panel and disconnect the electrical wires. Next, unscrew the heater from the wall and carefully lift it out. Finally, patch up any holes left in the wall and dispose of the heater properly.
What are the benefits of installing a wall-mounted heater and AC unit in a room?
Installing a wall-mounted heater and AC unit in a room provides efficient heating and cooling, saves space, improves air circulation, and allows for precise temperature control.
How do I turn on a wall heater?
To turn on a wall heater, locate the power switch or dial on the unit and set it to the desired temperature. Wait a few minutes for the heater to warm up and start producing heat. Make sure the area around the heater is clear and safe.
How do you remove gas wall heater?
To remove a gas wall heater, first, ensure safety by turning off the gas supply and power to the unit. Disconnect the venting and any electrical connections, then detach the heater from the wall by removing mounting screws. Carefully pull the unit away from the wall and cap the gas line to prevent leaks. If you're unsure or unfamiliar with gas appliances, it's advisable to consult a professional for assistance.
How can I effectively remove a baseboard heater?
To effectively remove a baseboard heater, first turn off the power to the unit. Then, remove the cover and disconnect the electrical wiring. Next, unscrew the unit from the wall and carefully lift it out. Finally, patch up any holes left in the wall from the removal.
Wall Heater Repair?
form_title=Wall Heater Repair form_header=8273 How would you best describe the problem?*= () No heat in one location () No heat in all locations () Excessive vibration (fan unit only) () Burning smell () Fluctuating heat () Thermostat not functioning properly Which kind of electric wall heating needs to be repaired?*= () Baseboard style () Wall fan unit
