0
It depends on the use of the 10 outlets. 20 amp is the norm. If this is in a shop with heavy loads then you would have to break them up.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How many 115 volt outlets could you run from a 20 amp breaker?
If you never plug anything into them, there is no limit. If the total current drawn from all outlets exceeds 20 amps, the breaker will trip.
How many electrical outlet can be install to a 30amps breaker?
A 30 amp breaker is usually used for a dedicated 30 amp device. Ordinary 15 amp receptacles can not be connected to a breaker of higher trip capacity than the rating of the receptacle. The wire size for a 30 amp breaker is #10 AWG.
How many outlets can you run on 15 amp 12-2 wire in canada?
No more than ten. If you used a 20-A breaker it would be up to 13.
Can you hook a 15 amp and 20 amp breaker to a breaker box using 20 amp wire?
No, you should use wire that matches the lowest amp rating of the breakers connected to it. In this case, you should use 15 amp wire since one of the breakers is a 15 amp breaker. Matching the wire gauge to the lowest amp rating ensures the wire is protected from overheating in case of a short circuit.
What power amp will you need to run 8 new plug sockets?
15 amp will run 8 outlets unless they are going to be heavily loaded. In that case use 20 amps.
Why do you need a 125 amp breaker for a 83 amp furnace?
If you put a 85 amp breaker in there it will overheat from the starting and stopping of the motor. The extra size of the breaker insures that the furnace will run without interruption and without overheating the breaker. And electric motor can draw three times the amperage rated on start up momentarily. This is why there is need of extra amperage ratings.
What amperage breaker to run 500 watt 240 volt heater?
To run a 500 watt 240 volt heater, you would need a 2.08 amp breaker. This can be calculated by dividing the wattage by the voltage (500W / 240V = 2.08A). You would typically round up to the nearest standard breaker size, which in this case would be a 3 amp breaker.
Can you run a 10 gauge wire 250 feet to the barn on a 120 amp breaker in the house If not what amp breaker should I use?
#10 cable is no good for 120 amps, you need #2 cable, and it can be used at a distance of 250 ft.
What is wrong with using eighty amp wire on twenty amp breaker?
It will work, but the draw backs are that the larger diameter wire is more expensive and it may not fit the 20 A devices well such as the breaker itself and any branch outlets or switches. It is also harder to run because of its bigger size. The voltage drop will be less across the larger wire, so that is likely the biggest advantage if you have a long run.
How many 110 volts can be ran on one breaker?
It depends on the amperage of the circuit breaker. For a typical 15 amp circuit breaker, you can run up to 12 outlets or receptacles. However, it is recommended to consult a qualified electrician to determine the appropriate number of outlets based on the specific electrical load requirements of the devices being used.
240v nema6-50r outlet wired with 6 gauge wire and 50 amp breaker you need to run a heater with a nema 6-30p can you simply put a 30 amp receptical in place of the 50 amp receptical?
Not legally because the rating of the 30 amp receptacle would have a 50 amp breaker ahead of it. If you reduced the feed breaker to 30 amps and still use the #6 wire, this would be within the electrical code rules.
Can you use a double pole 15 amp breaker in place of a 20 amp single pole breaker for a 12000 BTU air conditioner?
No, it is not safe to use a double pole 15 amp breaker in place of a 20 amp single pole breaker for a 12000 BTU air conditioner. The breaker size must match the electrical requirements of the appliance to prevent overheating and potential fire hazards. It is recommended to consult with a qualified electrician to ensure the proper breaker is used.
