0
This isn't filled like your normal standard stapler. First, pull up the top half of the stapler (the actual part that holds the staples and basically does all the work. Second, push in the two side buttons that are about 1/4 of the way down from the front of the stapling head. This will open the staplereservoir. There is a rod inside that has a round disc that comes out the back. Grab ahold of the disc and push in then lift up. This will release the rod. Pull the rod all the way back, as far as it will go. It doesn't come out, it will stop once it reaches the farthest back position. Lift the rod up to approximately a 90 degree angle. The staples go inside the opening that is now exposed. The basically rest along a rail. Push them in as far as they go and then return the rod you just pulled out and lifted up to it's natural parallel position. Push the rod back in, allowing the spring on the rod to create the tension needed to hold the staples in place and snap the catch clip near the back of the rod (just in front of the disc) back down into place. That's it! It sounds more complicated than it is but it's really not at all once you do it one time.
What else can I help you with?
What is the mean median mode and range of 108 490 502 502 502 and 518?
I have the same question lolz. All you have to do is: The mean of a data set is the sum of the values divided by the number of values. So... add up all of the numbers and divide them by 6, because there are 6 numbers. :) Hope this helps! Good luck!
What is the best estimate for 502 divided 6?
500/5 = 100
What is the probability of picking a red ace out of a standard deck of cards?
The probability of pick a red ace out of a standard deck of cards would be 1/26 because there are two read aces, the ace of diamonds and the ace of hearts.
Probability of drawing a spade or ace from 52 card deck?
Spade 25% Ace ~8%
What is the probability of getting an ace in a pack of cards?
you have a 1/13 chance of getting an ace in a pack of cards
Where can you buy staples for Ace Liner model 502?
Most office supply stores have staples for an Ace Liner model 502 stapler. Many lumber yards and home repair stores will also have them available.
What staples for Ace Liner 502?
After I searched this topic for our Vintage Ace Liner 502 stapler, I found they take standard staples but not the usual standard staples. These are Ace standard staples. I haven't bought them yet, but in looking at all the vintage Ace 502 staplers for sale the recommendation is standard staples, so it must mean their companies standard staples.
What size staples fit a Ace Liner Model 502 stapler?
The Ace Liner Model 502 stapler uses 1/4-inch (6mm) crown staples, specifically designed for light to medium stapling tasks. These staples are commonly available in various lengths, such as 1/4 inch, 3/8 inch, and 1/2 inch, depending on the thickness of the materials being stapled. Always ensure to check the specific requirements of your stapler for optimal performance.
How do you repair a ace liner 502 stapler. The top is jammed and metal side tabs won't move to release top of stapler. Whole top is jammed up somehow and stapler won't work. How best to unjam this?
i tapped mine lightly with a hammer and the top portion popped out and was able to open it up.
The staples are flaring out instead of in toward the center. How do you adjust ace liner 502?
Push the bottom plate forward with your thumb so the inward flared staple holes line up with the upper edge of the stapler. That lopsided square place on the bottom of the stapler just slides forwared and backward about a quarter of an inch.
Can you rehang the liner on your above-ground pool if it fell over in the winter?
You can rehang the liner on your above-ground pool if it fell over in the winter but you will need to remove the pool corner caps, the rail, and all of the water. You can then re-stretch the pool liner and refill the pool.
What is 20 percent of 502?
20% of 502 = 20% * 502 = 0.2 * 502 = 100.4
How do i reapir and indendation in an inground pool liner?
To repair an indentation in an inground pool liner, first, drain the pool below the level of the indentation. Smooth out the area by using a roller or your hands to push the liner back into place. If the indentation is due to air or water trapped behind the liner, you may need to create a small hole to release the trapped material and then seal it with a patch. Finally, refill the pool to check if the repair holds and the liner remains smooth.
What are the factors of 502?
The factors of 502 are: 1, 2, 251, 502.
What is 12 percent of 502?
12% of 502 = 502*12/100 = 60.24
How can I fix pool liner from pulling away from return hole?
To fix a pool liner that is pulling away from the return hole, first, drain the pool to a level below the return fitting. Carefully reattach the liner by smoothing it out and ensuring it is properly seated around the return hole. You can use a pool liner adhesive or tape for added security, and then refill the pool, ensuring the liner is evenly distributed as the water rises. Finally, check for any leaks around the return fitting and adjust as necessary.
What is 502 in roman numerals?
502 = DII
