0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Phenobarbitol gr ss PO ordered Have 15mg Tabs?
7.5
How do you clear a tab by using the ruler?
Double click the ruler > a "Tabs" panel should pop up. there you can see all the tabs (in length). Click on a tab you wish to clear then click clear. then ok.
What side of the work area does the open object tabs appear?
on the left hand side
What does an elevator on a plane do?
An elevator on a airplane are tabs on the tail that control its up and down motion in the air
Are the little tabs between inches on a ruler one centimeter?
No. There are 2.54 centimetres in an inch. The little tabs divide the inch into 16ths as I recall. the little tabs, which come in different sizes to denote different increments between each inch, are divisions of halves. ie, the inch is divided into one half, then each half into quarters, each quarters into eighths, each eighth into sixteenths, each sixteenth into thirty-seconds and on some rulers, each thirty-second into sixty-forths/
When a custom tab stop is set what happens to the default tab stops?
When you set a new tab, all default tabs prior to it are cleared. Default tabs after the last custom tabs that have been created will remain. So custom tabs override default tabs.
How do remove a default tab?
When you set a manual tab, all default tabs to the left of it are cleared. Tabs are only used when you hit the Tab key, so you would only clear the default tabs if you planned to use your own tabs.
Can you locate any tab stops that have been inserted into a document by looking at the horizontal ruler?
If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.If you look at the ruler you will see any tabs that have been manually set, as they will be on the ruler. Default tabs are shown below the ruler.
When do contextual tabs display in Office 2010?
Display commands for a selected object.
In word default tabs are set every?
every half inch
Word by default places a tab stop at every what mark on a ruler?
They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.
Where does word by default place the tab stop on the ruler?
They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.They are not placed on the ruler, but on the narrow bar underneath it. On manual tabs appear on the ruler. The default tabs are at every half an inch or 1.27 centimetres, which are equal values. It just depends on what measurement units you are using.
What type of tabs could only be set by using the Tab dialog box?
Only the default tabs can be exclusively set in the Tabs dialog box. Left, Right, Center, Decimal and Bar tabs can be set through the ruler. You can't set leaders for tabs there though, but they are not kinds of tabs.
In addition to the top level tabs Access displays other tabs called tabs that display when you perform certain tasks or work with certain objects such as data sheets?
contextual
What is leader tabs?
A character that comes before a tab stop
How far apart are the tabs placed in Microsoft Word?
0.5 inches or 1.27 centimetres is the default setting. That can be changed and in addition, users can add their own tabs of course.
What element of the word program window is used to display part of the document window?
tabs
