Yes, no problem whatsoever.
Yes, as long as the plug and receptacle match in pin configurations, it can be done.
What is the Process of Wiring If the device draws 15 amps (I thought Euro plugs were 16 amps or 6 amps, but no matter), you should not attempt to run it on a 10 amp supply. If the device needs less than 10 amps you could change the plug. Do please check that the smaller plug is 10 amps, not 6 amps. If you are trying to run a European device in the USA, the VOLTAGE is different (230 in Europe, 110 in USA) so the device won't run well. Don't even think of using an American device in Europe - there will be a big, expensive bang! (I know, I have seen the result).
That is 10 amp wire.
Sure, If you mean your stereo has 4 ohm output and using 16 ohm speakers. The volume will be reduced somewhat by doing this, but it won't harm the stereo. If you have 4 ohm speakers and stereo is designed for 16 ohms you can do it ,but the amp will run hot and you may suffer damage at high volume to the amp.
One would assume the chainsaw requires 120 volts or more if you want to run it with an inverter. If your chainsaw uses 16 amps at 120 volts then your wattage is Volts (120) x Amps (16) and that would be 1920 watts. So you will require a much larger inverter to run your chainsaw.
Provided the equipment draws less than 16 amps it can be supplied from a 16 A plug.
Yes, as long as the plug and receptacle match in pin configurations, it can be done.
Yes, as long as the plug and receptacle match in pin configurations, it can be done.
What is the Process of Wiring If the device draws 15 amps (I thought Euro plugs were 16 amps or 6 amps, but no matter), you should not attempt to run it on a 10 amp supply. If the device needs less than 10 amps you could change the plug. Do please check that the smaller plug is 10 amps, not 6 amps. If you are trying to run a European device in the USA, the VOLTAGE is different (230 in Europe, 110 in USA) so the device won't run well. Don't even think of using an American device in Europe - there will be a big, expensive bang! (I know, I have seen the result).
That is 10 amp wire.
8 amp in all but #9 and #10 , they get 16 amp
Sure, If you mean your stereo has 4 ohm output and using 16 ohm speakers. The volume will be reduced somewhat by doing this, but it won't harm the stereo. If you have 4 ohm speakers and stereo is designed for 16 ohms you can do it ,but the amp will run hot and you may suffer damage at high volume to the amp.
12 ga, 20 amp. 14 ga, 15 amp. 16 ga, 10 amp.
No you will not even get close to 1600 watts from that amp. If you read the spec for the amp they were putting 16-18 volts into the amp to get the claimed wattage. In your car you will be lucky to get 13.5 volts. You will see maybe 350 watts. A good rule when buying amps is a good amp will run about $1.00 a watt. So a $300 amp will be @ 300 or so watts.
One would assume the chainsaw requires 120 volts or more if you want to run it with an inverter. If your chainsaw uses 16 amps at 120 volts then your wattage is Volts (120) x Amps (16) and that would be 1920 watts. So you will require a much larger inverter to run your chainsaw.
Household circuits come in two flavors, 15 amp and 20 amp. Check the circuit breaker or fuse in your panel to see which one your outlet is wired to. If the outlet is on a 15 amp circuit, you could only run one, but if you have a 20 amp circuit, you could get away with two, assuming there are no other appliances plugged into the same circuit. The electrical code says circuits should be loaded to no more than 80% of the breaker's rating. for a 20 amp breaker, that works out to 16 amps. Your two lamps would draw 16.6 amps, so you would be right at the limit.
10