The Spa should be powered by a GFCI no matter how far away outlet is located.
Answer for USA, Canada and countries running a 60 Hz supply service.
Every receptacle in a bathroom is required to be GFCI protected. Outside of a bathroom, anything within 6 feet of the outside edge of a sink is required to be GFCI protected. The code does not define "sink" but any reasonable person would consider a spa as qualifying under this requirement. -- Sparkfighter
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Before the code requiring all outlets to have GFCI protection that at within 6' of a water source you were required to install the outlet at least 6' from the sink. Now, there is no minimum distance but all outlets must be GFCI protected that are installed within 6' of a water source.
Ground wire is loose or disconnected somewhere in that circuit.
Not if the GFCI breaker is supplying the circuit you are wanting to put the GFCI receptacle into.
No, except that you insert the wires into the holes on the back of the outlet. The power in connects to the LINE side of the outlet and power out connects to the LOAD side of the outlet. This is clearly marked on the back of the outlet. This will not only protect the outlet with the GFCI installed but all outlets receiving their power from that GFCI. If you do not want to protect the outlets receiving power from the outlet then connect that outgoing wire to the LINE side also. But know that only the outlet with the GFCI will be protected and all other outlets will not be GFCI protected.
I assume you are hard wiring it and not plugging it in. The power coming into the GFCI outlet connects to the line side of the GFCI outlet. If you want the outdoor timer protected by the GFCI then connect the wire going to the timer to the load side of the outlet. If you do not want the timer protected then connect it to the line side. On the back of the GFCI if you look closely you will see Line & Load marked on the back.
This article explains it in detail: Learn How To Safely Install a GFCI Outlet at The Home Depot
An electrical outlet can not be placed behind a sink. If the outlet is witin 6 feet of a sink it must be GFI protected.
Before the code requiring all outlets to have GFCI protection that at within 6' of a water source you were required to install the outlet at least 6' from the sink. Now, there is no minimum distance but all outlets must be GFCI protected that are installed within 6' of a water source.
GFCI Breakers are quite a bit more expensive than a GFCI outlet. More often than not a typical residence will need only a handful of GFCI outlets that combined together will be cheaper than a GFCI breaker. If you need to protect a series of outlets with GFCI protection you can simply connect the rest of the outlets on that same circuit downstream from the first outlet on the line and make that the GFCI. All you have to do is connect all the other outlets to the LOAD side of the GFCI outlet. If a GFCI fault occurs in any of the outlets down stream they will trip that very first GFCI plug you placed and keep you safe.
Yes. You can wire more than one gfci to a circut.
Not if the GFCI breaker is supplying the circuit you are wanting to put the GFCI receptacle into.
Ground wire is loose or disconnected somewhere in that circuit.
Yes, but you can feed multiple outlets from one GFCI outlet. Make the first outlet fed in the cicuit a GFCI. Search for GFCI outlet with Google, etc. and I'm sure you will find an explanantion of how. Most GFCI's come with instructions also.
No, except that you insert the wires into the holes on the back of the outlet. The power in connects to the LINE side of the outlet and power out connects to the LOAD side of the outlet. This is clearly marked on the back of the outlet. This will not only protect the outlet with the GFCI installed but all outlets receiving their power from that GFCI. If you do not want to protect the outlets receiving power from the outlet then connect that outgoing wire to the LINE side also. But know that only the outlet with the GFCI will be protected and all other outlets will not be GFCI protected.
Yes you can. Lots of blow dryers have GFCI protection built in.
In a word NO, that will not cause either GFCI to trip. The correct term is GFCI (Ground Fault Circuit Interrupter)
I assume you are hard wiring it and not plugging it in. The power coming into the GFCI outlet connects to the line side of the GFCI outlet. If you want the outdoor timer protected by the GFCI then connect the wire going to the timer to the load side of the outlet. If you do not want the timer protected then connect it to the line side. On the back of the GFCI if you look closely you will see Line & Load marked on the back.