0
by a parellal current switch.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you wire a light and switch with the 2 wire old romex?
with a standard 1 pole light switch (one switch operating the light) it is black wire to black wire and white to white (non grounded)
How do you wire a light to a switch at the end of a run and which controls an outlet?
Bring power into the light switch box 12/2 or 14/2 wire depending on the existing wire. Make sure you use the exactly same size wire that is used on that circuit. If you do not know look at the breaker in the main panel that controls power to that circuit. 20 amp will be 12/2 wire and 15 amp will be 14/2 wire. Now run another wire from the switch box out to the outlet. Inside the switch box, strip both white wires back 3/4" and connect them together under a wire nut and push this back into the box. Connect the 2 ground wires together and then connect that to the ground screw on the switch. You now have 2 black wires left. Connect them to the 2 screws on the light switch. Does not matter which black wire you connect to which screw. At the outlet connect the ground wire to the green ground screw, black wire to copper screw, and white wire to silver screw. That outlet will now be controlled by the light switch.
How do you wire a one light to be operated from 4 location?
you will need 2-3way switch and 2-4way switch
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
When at a 2 pole light switch and the wire colors shown are black white and green which is the hot wire and which is the common?
the black wire is the hot wire
How do you wire a two way switch one controls the outlet the other the outdoor light with a pigtail?
You need two separate switches. You can get two switches that are in the same form factor as a single switch (2 gang switch). You use one switch for the outlet and the other for the light. You switch the black wires which are "hot".
How do you connect two way electrical switch?
The two way switches work in pairs. We find most of them in our houses where the light bulb can be operated by two switches each at the far end to the other. Each switch consists of three terminals two of which are connected. When one switch is open and the other is closed then the bulb glows and viceversa
How do you get electricity to a wall switch when getting electircity from an outlet?
Simply run a wire from that outlet to that wall switch. Be sure you use the exact same wire size that you find in that outlet. It will be AWG 12/2 or 14/2. Do not mixes wire sizes. Connect the ground to green ground screw at outlet, and white wire to silver screw, and black wire to gold screw. At the light switch connect all white wires together under a wire nut and push them back into the box. Connect the ground wire to the green ground screw on the switch. Now connect the 2 black wires you have left, power in and power out, to the 2 screws on the switch. Does not matter which wires you connect to the 2 screws.
How two wire 2 light switch up in 1 box?
Tie all the white wires together under a wire nut and push them back in the box. Tie the black incoming power wire and outgoing power wire, if there is one, together under a wire nut with a black wire pigtail. Connect this pigtail to one screw on each light switch. Connect the black wire going up to the lights to the appropriate switch you wish to use to control that light.
How do you wire a 20A switch which comes with a neutral wire when only 2 wires are available for the circuit?
You never switch a neutral wire, only hots. hooking both hot and neutral to the same switch will result in a short when the swith is turned on.
Can you by pass the AC pressure switch?
If it is a 2-wire switch- yes If it is a 3-wire switch- no
Have 3 lights Power to light 1 Need to connect light 2 then light 3 then down to single pole switch How do you wire?
You would wire the switch to the first light. Code says to break the black or power side of the circuit. Connect the white to the light. Take the black down to the switch on the black wire and back to the light on the white. This is a line of wire from the light to the switch. From the first light, take the white and the return white from the switch to the second with another run of wire. This will be regular black white with ground. White to white and at the first light the return line from the switch is white but hook to the black to the second light. Second light to third just continues the two wires. Black to black, white to white. I think this is clear enough to follow. If not, ask again.
