0
It will taken 8 amps
<<>>
The conversion of 2.5 sq mm wire to AWG is equal to a #12 wire. The ampacity of a #12 copper wire with an insulation factor of 90 degrees C is 20 amps.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How many amps can a 8 gauge wire run coming from the ditribution panel to the sub panel 25 feet away?
A #8 copper wire with an insulation factor of 75 or 90 degrees C is rated at 45 amps.
Can you run a 2 kw convector heater through a 25 amp trip switch at 240 volts?
Yes, the total amperage load of a 2000 watt heater at 240 volts is 8.3 amps. Keep in mind that the wire feeding the heater must be a #10 because the breaker is rated at 25 amps. A wire's ampacity rating can be larger that the breaker amperage rating but never smaller. Example, a #14 rated at 15 amps or a #12 rated at 20 amps can not be connected to a 25 amp breaker. The 25 amp breaker does not trip until it reaches 25 amps well over the allowable amperage of the #14 amd #12 wire. This is why a #10 wire must be used as its rating is 30 amps.
Should 25 amps breaker be replaced by 20 amps?
For typical residential house wiring 12 AWG wire is required for a 20 Amp breaker. If you change out the breaker for a 25 A breaker you would have to rewire the circuit with 10 AWG. In that case you could up the breaker to 30 Amps. All outlets and switches should be rated at the same voltage and current as the breaker.
Can you use 10 AWG wire to run 6000 watts of light drawing 30 amps?
I'm assuming the electrical system is single phase, such as a home. If not, you need to hire someone to do the work for you. First, 6000 watts at 120v is 50 amps, so if your load is truly 6000 watts, 30 amps isn't enough. If your 6000 watts is 240v, which would draw 25 amps, then 30 amps is plenty. Ten gauge wire may not be placed an a breaker or fuse larger than 30 amps.
How do you replace a 15 amp circuit to a 25 amp circuit?
You have to rewire the circuit completely with 10 AWG wire and replace all outlets and switches with devices rated at 25 Amps. Note 25 Amp breaker is an unusual size. 10 AWG will go up to 30 amps, and that would be the way to go.
How many amps can 16 gauge wire carry at 120 vac at 25 feet?
18 amps.
How many amps can 8 gauge wire carry at 120 vac at 25 feet?
A #8 copper wire with an insulation rated at 75 or 90 degrees C is rated at 45 amps.
How many amps can a 8 gauge wire run coming from the ditribution panel to the sub panel 25 feet away?
A #8 copper wire with an insulation factor of 75 or 90 degrees C is rated at 45 amps.
What is the danger if you replace a 15 amp circuit breaker with a 25 ampere breaker?
If the wire used on the circuit is sized for 15 amps (usually 14 gauge) you run a very serious risk of fire.If the wire used on the circuit is sized for 25 amps (usually 10 gauge, good for 30 amps) there is no increased danger.Additional InformationIf you don't know if the wire is sized for 25 amps, DON'T DO IT!A 25 amp circuit would require 10 AWG wire. The fire hazard mentioned above is real and you shouldn't ignore that advice.
Can you run a 2 kw convector heater through a 25 amp trip switch at 240 volts?
Yes, the total amperage load of a 2000 watt heater at 240 volts is 8.3 amps. Keep in mind that the wire feeding the heater must be a #10 because the breaker is rated at 25 amps. A wire's ampacity rating can be larger that the breaker amperage rating but never smaller. Example, a #14 rated at 15 amps or a #12 rated at 20 amps can not be connected to a 25 amp breaker. The 25 amp breaker does not trip until it reaches 25 amps well over the allowable amperage of the #14 amd #12 wire. This is why a #10 wire must be used as its rating is 30 amps.
What size wire to carry 25 amps 170 ft?
To answer this question a voltage must be given.
What size wire needed for 25 amps 220 volts for 75 feet?
10 AWG in copper.
What is amperage limit of 12 AWG stranded copper wire?
A #12 copper wire with an insulation factor of 75 or 90 degrees C is rated at 20 amps.A 12 AWG wire should not be connected to a breaker larger than 20 amps. The wire is capable of carrying that current load without overheating and causing fire.
How many amps in 25 ma?
.025amps
What gauge wire would you use to wire a 120V 20A motor?
I am assuming that this is a one and a half HP motor. To wire a 120V 20A motor the electrical code states that the conductor has to be 125% of the motor's full load amps. This equals 25 amps. There is no wire rated at 25 amps so the next size up is 30 amps. A #10 copper wire with an insulation factor of 60, 75 and 90 degrees C is rated at 30 amps. To carry this to a conclusion This #10 wire should be protected by either 60 amp non time delay fuses or 35 amp time delay fuses or a two pole 50 amp breaker.
How many watts for a 25 amp fuse?
# 10 wire is rated at 30 amps. Code states the the wire is only to be loaded to 80%. 80% of 30 = 24 amps. If distance is a factor then the resistance of the wire comes into play. Go up one size to #8 rated at 40 amps, usable 32 amps.
What gauge wire is required for 25 amps over 100 ft at 240 volts?
10 AWG copper.
