0
Assuming the can lights is all that will be on this 15 amp 120 volt circuit and each one has no more than a 75 watt bulb installed you can install up to 19. This is determined by multiplying the amps x the voltage to get the wattage. 15 x 120 = 1800. Then multiply the 1800 x 80% and you get 1440 which places an 80% load on the circuit which is all you safely want. You then divide the 1440 by 75 which is the wattage of each bulb and you get 19.2. You could add more if you use fluorescent bulbs but someone could come along later and install incandescent bulbs and overload the circuit. So stick with no more that 19 to be safe. Remember this is a 15 amp ciruit so you must use AWG # 14 wire and not #12. If you use AWG #12 and a 20 amp breaker you can have 25 can lights with 75 watt bulbs on the circuit.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How many electrical outlet can be install to a 30amps breaker?
A 30 amp breaker is usually used for a dedicated 30 amp device. Ordinary 15 amp receptacles can not be connected to a breaker of higher trip capacity than the rating of the receptacle. The wire size for a 30 amp breaker is #10 AWG.
Can you use a 2 pole 60 amp breaker to feed one circuit?
No, you cannot use one in place of the other.
Is it ok to run three 240 on one 50 amp breaker?
If you are asking, can three separate 240 volt circuits be run off of one 50 amp breaker then the answer is no. Not without knowing what the loading of the three circuits are and whether all three circuits could be on at the same time.
How many 20amp outlets in commercial building per circuit?
All depends on how big your main breaker is and what size wire you are using,one 20 amp outlet needs #12 wire not more than 50feet away from main breaker
What size breaker is needed to supply a sub panel that is feeding a range and dryer?
If there is a possibility of both operating simultaneously, then a 100 amp breaker (actually 80 amp if you can find one), and appropriate wiring would be required. Even if they were not expected to operate simultaneously, it would be prudent to wire as if they were.
Can you replace your current cooker fuse 30 amp with a 40 amp circuit breaker?
A 30 amp breaker is designed to trip at an earlier point than a larger 40 amp breaker so one appliance that operates on lower amperage level could be unsafe or damaged before it could trip the higher 40 amp breaker. Also, the existing wiring may not be rated for 40 amp service.
Can you change a 250v 15 amp breaker with a 115v15 amp breaker?
No, it would not be safe because 250v is too high for that breaker. <<>> In North America all household breakers are rated at 120/240 volts. A 250 volt 15 amp breaker would would be a two pole breaker and take up two slots in the distribution panel. This can be pulled out and replaced with two separate 15 amp breakers or one 15 amp breaker and a slot panel filler to cover the second slot.
How many wires can be connected on to a 20 amp breaker in NH?
Code only allows one wire to be connected to a single pole breaker. Any additional circuitry has to be done in a junction box downstream from the breaker.
Can multiple circuits be connected on one breaker?
Multiple wires can be connected to one breaker but the one breaker IS a circuit. As long as the load is not more than 80% of the breaker capacity (example: a 20 amp breaker can only have 16 amps or 1920 watts at 120 volts) then by code as long as the load is not a specialty outlet of some sort, you can have as many outlets you want.
Which terminal on a 15 amp household breaker does the hot wire feed into and which one does it come out?
On a 15 amp household breaker there is no terminal on the in feed of the breaker. The breaker either plugs into the distribution panel's bus bar or it bolts to the distribution's bus bars. The feed conductor connects to the load side of the breaker at its terminal lug.
Can you use a 60 amp breaker for a airconditioner with heat instead of two thirty amp breakers?
No. If your AC is currently running on a 30 amp 2 pole breaker, then it is a 220 volt unit. You cannot substitute one 60 amp single pole breaker as you'll only be supplying 110 volts and the AC unit won't work. In fact you could damage it.
If you have a 200A Meter Main Combo do you need a main 200A breaker in the panel?
When I went to a 100 amp service I could not find a 100 amp. breaker in stock. I used a 60 amp. breaker and have never blown it. The 200 amp you are using can handle up to 200 amps, but if you use a smaller breaker it will only handle up to that amperage. The 200 amp is usally the total amperage of all the breakers comming out of the box. You will probably never come anywhere near using 200 amps at one time.
Why will too many electrical devices operating at one time after blow a fuse or trip a circuit breaker?
The load exceeds the limit of the breaker or fuse. For example a 20 amp breaker on a 120 volt circuit will handle 2400 watts. Exceed that wattage and the breaker will trip or the fuse will blow.
How many electrical outlet can be install to a 30amps breaker?
A 30 amp breaker is usually used for a dedicated 30 amp device. Ordinary 15 amp receptacles can not be connected to a breaker of higher trip capacity than the rating of the receptacle. The wire size for a 30 amp breaker is #10 AWG.
You have an elecwaterheater it blows the20amp in line breaker and the 50 amp main?
For a main breaker to trip under these circumstances the rest of the panel is becoming close to its load rating. When the 20 amps breaker trips the rest of the panel is close to or over 30 amps, the 20 amp breaker takes it over the top. What trips a HWT breaker is usually a faulty heating element. It could be the top one or the bottom one.
Can you had a 20 amp breaker on your 70 amp sub-panel that has already 70 amp total on it that consist of one 50 and two 15 amp breakers and the panel has 4 available spaces out of 8?
SeeIf_a_100A_breaker_panel_has_five_15A_breakers_and_four_20A_breakers_could_this_overload_the_panel
I have a 15 amp tool hooked up to a 15 amp breaker- This trips the breaker even with nothing else running- There is also a GFCI outlet on the same circuit- Is the breaker or GFCI bad?
A 15 amp breaker will trip at 15 amps at an ambient temperature of 104 degree F. If the ambient temperature is higher the breaker will trip before 15 amps and if the ambient temperature is lower the breaker will trip after 15 amps. I would suspect the circuit is overloaded. But, you can change the breaker and see what happens. Just swap it with another one.
