No more than 13.
The NEC allows multiple 20A receptacles on a 20A circuit. The T-shaped neutral slot on a 20A receptacle is designed to accommodate both 15A and 20A plugs, but it does not imply that no other outlets can be on the circuit. As long as the total connected load does not exceed the circuit's capacity, multiple receptacles can be connected.
Go to your distribution panel and shut off the breaker that you think is the circuit in question. If the circuit becomes de-energized then the breaker you just turned off feeds that circuit. Look on the handle of the breaker and the number you see is the amperage of that circuit. <<>> Determination of a 15 or 20 Ampere circuit is normally indicated by a combination of a 20A breaker and a 20A dedicated outlet. A 15A circuit normally has multiple outlets; not typical in a 20A circuit.
Assume a single breaker controlling a number of outlets. The black wire is HOT, the white wire is Neutral and the green or bare wire is Ground. The wires and outlets should match the rating of the breaker in Amps. Typically 15 A for 14 Gauge wire. (I prefer 20A outlets and 12 gauge wire). You must calculate the expected load at each outlet. The electric code may be different in each locale, but 8 to 10 outlets on a circuit might be typical for general usage. That is over an amp per outlet. If you had a situation where you knew you would be plugging in a high amp device liek an electric heater you might only have 1 outlet on circuit. You wire the outlets in a circuit in parallel and make certain each is wired identically. The Black wire should always be on the copper colored screw and the white on silver screw and the ground on the green screw. For a couple of bucks you can buy an outlet tester. It is usually yellow with a three prong plug and lights that tell you if an outlet is wired correctly with power turned on. The lights identify problems based on which lights are lit.
No, it is not safe to install a 20A outlet on a 15A circuit. The outlet should match the circuit's amperage to prevent overloading and potential fire hazards.
No, it is not safe to install a 15A outlet on a 20A circuit. The outlet should match the circuit's amperage to prevent overheating and potential fire hazards.
While 7 is pushing the upper limits, the main concern should be "what will the outlets be running? If you're putting a freezer out there, it should probably be on a separate circuit. If you'll be running any high amperage equipment; again, put it on a separate circuit.
If you know what you're doing, you can probably accomplish that in a 1A circuit.
It will depend on how big the circuit is if its a 20a no if its 40a yes!
20 amp circuit breaker
I'm going to assume you are referring to residential construction because rules for commercial and industrial settings can be different. Also rules differ by geography (i.e. Canada specifies a maximum of 8 outlets on a 15 amp circuit, USA code is silent on the issue but for practical purposes, more than about 10 will likely lead to poor performance. Some code also specifies max loading of a 20 amp circuit at 80% making 10 outlets the practical limit if using 20 amp outlets on that circuit.To expand on the previous answer a little, there is a large margin of safety in the construction of these components but if you think about it, you are placing a component that is rated at 15 amps into a 20 amp circuit. That outlet is potentially the weakest link in the circuit and could act like a fuse. If any of those 15 amp outlets are overloaded, it might overheat and fail before the circuit breaker. This is a recipe for a fire. You may think now that you'll remember to only plug in light loads, but these things have a habit of growing.You can plug typical small home appliances (lamp, stereo, TV, etc.) into a 20 amp outlet so the only benefit in using the 15 amp outlet is the minor cost savings at installation. If it were my building, I wouldn't risk it.If I can't talk you out of doing this and it's allowed by your applicable code, make sure you don't daisy-chain the circuit through the outlets. (In other words, don't run your 12-2 wire in one side of the outlet and out the other side.) Instead, use a pigtail (short piece of wire) to tap off your line to each individual outlet. In the United States you can run 20 amp breakers with 15 amp outlets but not in Canada. And for how many? About 10 to be on safe side as long as they are all low amp usage appliances. TVs, steros, fans, lamps.You can run 20 amp breaker with 12-2 wire as long as you make sure you use the 12-2 wire that is rated at 20 amp.Whilst this was not your exact question it is worth saying IT IS NEVER SAFE to run a 20 amp load through a 15 amp receptacle. It is only rated to handle up to 15 amps.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
No, it is not safe to use a power strip to connect multiple pieces of equipment that each require a dedicated 20A outlet. This can overload the circuit and pose a fire hazard. It is recommended to consult with an electrician to install the appropriate outlets for your equipment.
With a 15 A breaker you need 14 Gauge wire. Normally you would only put 8 outlets on a 15 A circuit. If you have the option you shoudl consider a 20 A circuit, use 20A receptacles and 12 gauge wire. Comment: The question was on a homeowners electrical exam. My answer was also 14 gauge however, the tester said the answer was 12 ga. I thought maybe there was something special about the 10 outlets. For example, 10x180 VA per outlet/120V = 15 A which is right at the limit for 14 ga but would be 75% for the 12 ga wire.