0
AN hardware is 1/16" per digit, so AN4 is 1/4", AN6 is 3/8", AN8 is 1/2" and AN12 is 3/4" or 12/16"
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What does the grade 8.8 bolt identification refer to?
he diameter of the bolt.
How do you find inner diameter and outer diameter of the bolt?
by using a caliperhttp://www.technologystudent.com/equip1/vernier3.htm
How can I find the diameter on 12 inches?
A diameter is a property of circular objects. "12 inches" is not a circular object and so cannot have a diameter.
What is the circumference and diameter of 12 inch circle?
Circumference = 37.7 inches Diameter = 12 inches
A carpenter has a bolt with the diameter 0.3125 inchesWill the bolt fit in hole made by a drill bit with diameter 0.3 inches?
if the diameter 5/16 inches then you covert the 5/16 into 0.3125 inches. divide 5 by 16=0.3125 which is a little bigger than 0.3! ;)
An automotive bolt has a designation of 12-13 unc auto technician a says the bolt is a coarse thread bolt auto technician b says the bolt has a diameter of 13millimeters which of the statements is co?
The first technician is correct, it is a coarse thread. I'm not sure there is a bolt called 12-13 so I am assuming you meant 1/2 - 13. Wich would be a bolt 1/2 inches long. The diameter of a #13 unc bolt would be ( 13 x .013in ) + .06 = .229 inches in diameter.
What do you mean by gross diameter of bolt?
This would be concidered the largest diameter,dimension of a bolt.
What does the grade 8.8 bolt identification refer to?
he diameter of the bolt.
Stress on minor diameter of bolt when bolt is subjected to longitudinal force?
The stress on a bolt under longitudinal force is the total force on the bolt divided by the stress area. The stress area is a little bigger than the minor diameter area, calculated from the average of the minor diameter and pitch diameter. The total force on the bolt is its torque preload plus the (bolt stiffness/(bolt +member stiffness) x (externally applied load )
How do you measure lug patterns?
On a five bolt pattern measure from outer edge of one bolt then across to the middle of another skipping one bolt hole( not quite the diameter). On six or four bolt patterns measure across from bolt center to bolt center as you would the diameter if it were a circle.
What does a bolt's wrench diameter mean?
That refers to the size wrench necessary to tighten or loosen the bolt.
What is necked-down bolt?
If a bolt is tightened past a certain point, it deforms by stretching, with the result that its diameter is reduced, if it is tightened past the elastic strain limit of the metal the reduction in diameter is permanent. This can often be seen afterwards in a reduced-diameter 'neck' in the shaft of the bolt where the highest stress occurred.
How do you find inner diameter and outer diameter of the bolt?
by using a caliperhttp://www.technologystudent.com/equip1/vernier3.htm
How you find the pcd of flange?
PCD (Pitch Circle Diameter) is the diameter of a circle that goes through each of the bolt holes. You can find it by measuring distance from centre of one bolt hole to the centre of opposite end bolt hole...
What is the bolt pattern and diameter for Lexus Ls430?
um i have no idea!!
What is the circumference of a circle with a diameter of 12?
The circumference of a circle with a diameter of 12 is about: 37.7 (C = diameter x Pi).
What do you mean by bolt of uniform strength?
Bolt of uniform Strength means that the entire length of the bolt is subjected to same intensity of stress,that is stress in the shank portion and the threaded portion are same.this is achieved by reducing the diameter of the shank to core diameter of the thread.
