0
You could if it fit properly in the connector, but it would be massive overkill since you only need 12 AWG wire. You also have to make sure the load can physically accommodate that larger size wire.
Every so often someone will replace an electric cooktop witha gas one. All of the new gas cooktops require a 110v outlet. The old electric cooktop may have been run with a 50 amp breaker (and probably 6 gauge wire) In order to convert this 220 v circuit to a 110v circuit we change to a 20amp breaker. Depending upon the brand of breaker sometimes the wire will fit into it. If not, we splice on a short piece of 12 gauge wire and then connect to the breaker.
Add your answer:
Earn +20 pts
Can you use 14 wire for a light off a 20 amp circuit?
Yes, in home wiring as long as it is protected by a 15 amp breaker. Remember this circuit will only handle 1800 watts and cannot be loaded to any more than 1440 watts. So if each light is 75 watts then the maximum you can install is 19.
What will happen if a wire that is plugged in heats up?
its casing will dry out, crack and catch fire, or it will crack off and cause arking, which can cause a fire... ultimately, check the gauge size of the circuit and make sure it corresponds to the proper amperage of breaker, if this is all good, you need a bigger cord(the gauge size must be sufficient for the intended tool/device.. a drill that has a 16 amp rating needs a 12 gauge cord whereas a 12 amp drill needs only a 14 gauge cord.
What can you run off a 50 Amp breaker?
Anything that does not pull over 50 amps.
Have 240v 30amp breaker need to connect a 240volt 40 amp cooktop can you do this I have a 103 600volt wire the cooktop power supply requires 240volt 4 wire 60 hz?
Yes you can. As long as you don't use 40 amps. The 30 amp breaker may kick off if you use all things at once. So you are well protected but not up to code. The 4th wire required for the new stove is probably a ground fault wire. So run a new cable or cook slower.
How can you prevent fires from electrical equipment?
This depends entirely on what you are doing. You can prevent static shocks be wearing tighter clothing, and avoiding wool and nylon. You can prevent being shocked by the wall outlet by using protective outlet covers. When working with hobby electronics, there is little more necessary then caution. Once the voltage you are working with surpasses about 1000 volts or so, there is nothing you can do except keep your distance, and pass it off to someone experienced in dealing with high voltage.
What gauge wire to run off a 20 amp breaker?
Use AWG 12/2 with ground.
Can you run 8 gauge wire on a 50 amp breaker?
No, you should not run 8 gauge wire on a 50 amp breaker. The wire size should be compatible with the amperage rating of the breaker to ensure safety and prevent overheating. For a 50 amp breaker, you should use a minimum of 6 gauge wire.
Is it ok to exchange a 20 amp breaker with a 40 amp breaker?
No, it is not okay to replace a 20 amp breaker with a 40 amp breaker. Breakers are designed to protect the electrical wiring in your home, and using a higher amp breaker can overload the circuit and create a fire hazard. Always use the correct amperage breaker for the circuit.
How do you wire a 15 amp breaker?
Ground wire connects to the ground bar, white wire connects to the neutral bar, and black wire connects to the breaker. Be sure and turn off main breaker before installing the wire or the breaker.
Can you use 14 wire for a light off a 20 amp circuit?
Yes, in home wiring as long as it is protected by a 15 amp breaker. Remember this circuit will only handle 1800 watts and cannot be loaded to any more than 1440 watts. So if each light is 75 watts then the maximum you can install is 19.
How do you replace a 15 amp breaker in the circuit box?
To replace a 15 amp breaker, first shut off the main power to the circuit box. Then, remove the cover of the circuit box and unscrew the old breaker. Disconnect the wires attached to the old breaker, connect them to the new 15 amp breaker, and securely screw it in place. Finally, turn the main power back on to restore electricity.
Can you safely change a 30 amp breaker to 20 amps?
No, this is not a recommended procedure. The breakers main job is to protect the wire that is connected to it. A 20A breaker will have a #12 wire (rated 20A) connected to it. A 30A breaker will have a #10 wire (rated 30A) connected to it. As you can see if you use a 30A breaker on a #12 wire you could overload the wire by 10 amps. I have seen an incident where the insulation has melted off of an overloaded wire, the wire short out and a fire start before the bigger size breaker tripped. DON'T DO IT.
Why does an Electric circuit breaker have a melted wire?
Wow that is hugely dangerous and a risk of fire. They get hot because you are running a large amperage through them, melting cause it is overloaded. For example. If you had a 20 amp breaker, and 12 gauge wire (20A), and a 15 amp recepticle. Then the most you would want to run on that recepticle is 12 amps continuously, 15 amp peak non continuous. If you replaced the recepticle with a 20 amp recepticle you could run 20 amp peak, or 16 amps continiously. You could not go with a higher amp outlet as the circuit only has 12 gauge wire, and a 20A breaker. If you plugged something with a 30 amp draw into said outlet you would get the outlet hot. find out how many amps you are drawing off the outlet in question, then check the gauge of the wire in the wall, and the rating of the outlet and breaker that outlet is off of. Then we could decide what to do next. Well,Being a Electrician, my advice is if you have to ask question about that call a Electrician IMMEDIATLY!!!!It could be a number of things.A loose wire in the back of plug in,worse yet a broken wire that keeps rubbing together ,(EXTREME FIRE HAZARD)Electricity is nothing to fool with if you are not trained.BE SAFE<SMART.Turn circut breaker OFF.CALL ELECTRICIAN Really,cmon. Residential pulling that much power off ! outlet.....look outside the box!!how old is house would be first question
Can you wire 15 amp plug on a 20 amp circuit?
Yes, you can wire a 15 amp plug on a 20 amp circuit, as long as the wiring and breaker are compatible with the 15 amp load. It's important to use the appropriate wire gauge for the load and ensure that the circuit breaker is sized correctly to protect the wiring.
Can you run an 110v air conditioner continuous that draws 7.5 amps off of 14 gauge wire with 15 amp breaker?
It is not recommended to run an 110V air conditioner drawing 7.5 amps off of 14 gauge wire with a 15 amp breaker. Typically, 14 gauge wire is rated for a maximum of 15 amps in normal operating conditions, which could pose a safety risk if the air conditioner draws the full 7.5 amps continuously. It is advisable to use a wire gauge that can safely handle the current draw of the air conditioner to prevent overheating and potential electrical hazards.
What will happen if a wire that is plugged in heats up?
its casing will dry out, crack and catch fire, or it will crack off and cause arking, which can cause a fire... ultimately, check the gauge size of the circuit and make sure it corresponds to the proper amperage of breaker, if this is all good, you need a bigger cord(the gauge size must be sufficient for the intended tool/device.. a drill that has a 16 amp rating needs a 12 gauge cord whereas a 12 amp drill needs only a 14 gauge cord.
Can a 20 amp breaker be replaced with a 15 amp breaker?
It is not recommended to replace a 20 amp breaker with a 15 amp breaker unless the wiring is also changed to accommodate the lower amperage. The breaker should always be sized to the electrical load it is protecting to prevent overheating and potential fire hazards.
