answersLogoWhite

0

6ga should be used. It might not be against codes where you are,and you might

have a 50amp installed for something that only uses 40amp, but it should be done right,

and 6ga should be used off of a 50amp breaker.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Natural Sciences

Can you connect 14 gauge wire to 12 gauge wire on a 20 amp breaker if the 14 gauge is the end of the run and dedicated to lights?

yesAnother (corrected) answer.NO! The circuit breaker is there to protect the wiring from overheating. It wouldn't matter where on the circuit you decided to put the 14 gauge wire, you would need to change the breaker to 15 Amp if you did that. Using 14 gauge wire on a 20 amp circuit is a fire hazard and contrary to UBC. Contact your local building and zoning department to verify.


What size main breaker do you need to run 10 gauge wire?

The size of the main breaker depends on the maximum current rating of the 10 gauge wire and the load it will be powering. Typically, a 10 gauge wire is rated for a maximum current of 30 amps. Therefore, a 30 amp main breaker would be suitable for running 10 gauge wire. However, it is important to consult local electrical codes and consider the specific load requirements before making a final determination.


Can you run a 10 gauge wire 250 feet to the barn on a 120 amp breaker in the house If not what amp breaker should I use?

#10 cable is no good for 120 amps, you need #2 cable, and it can be used at a distance of 250 ft.


Can you hook a 15 amp and 20 amp breaker to a breaker box using 20 amp wire?

If the full load amps rating of the motor on the name plate is exactly 15 amps you need to use # 12 wire. If it is a longer run you may have to go up one more wire size. The breaker size you need is 30 amps.


How do you wire 15amp 230v woodworking machine. 10agw or 12agw wire and type of outlet. Into a 15amp or 20amp breaker?

A 20 amp circuit with #12 gauge wire will work in any event but if the nameplate recommends a 15 amp circuit then #14 gauge wire on a 15 amp circuit is sufficient. In either case you will have a double pole breaker and your equipment may not require a neutral. Always run a grounding conductor.

Related Questions

What gauge wire do you run between a 30 amp breaker and an outlet?

10 AWG.


Can you connect 14 gauge wire to 12 gauge wire on a 20 amp breaker if the 14 gauge is the end of the run and dedicated to lights?

yesAnother (corrected) answer.NO! The circuit breaker is there to protect the wiring from overheating. It wouldn't matter where on the circuit you decided to put the 14 gauge wire, you would need to change the breaker to 15 Amp if you did that. Using 14 gauge wire on a 20 amp circuit is a fire hazard and contrary to UBC. Contact your local building and zoning department to verify.


What gauge wire to run off a 20 amp breaker?

Use AWG 12/2 with ground.


How should I properly wire a 30 amp breaker for my electrical circuit?

To properly wire a 30 amp breaker for your electrical circuit, you should use the appropriate gauge wire (typically 10 gauge for a 30 amp circuit), connect the wire to the breaker terminal, and then run the wire to the outlet or device you are powering. Make sure to follow all local electrical codes and safety guidelines when performing this task.


What size main breaker do you need to run 10 gauge wire?

The size of the main breaker depends on the maximum current rating of the 10 gauge wire and the load it will be powering. Typically, a 10 gauge wire is rated for a maximum current of 30 amps. Therefore, a 30 amp main breaker would be suitable for running 10 gauge wire. However, it is important to consult local electrical codes and consider the specific load requirements before making a final determination.


What size wire for 75 feet of wire for a 30 amp 220 volt oven?

A 30 amp breaker run 75 feet would require you use AWG #10 wire. But, an oven normally pulls more that 30 amps and I would not use #10 wire on a 30 amp breaker for an oven. Normally any newer oven is wired with AWG #6 gauge wire on a 50 amp circuit breaker so the breaker will not trip during heavy use of the oven. Some older ovens could use a #8 wire on a 40 amp breaker.


Can you use 600v 14 gage wire on a 240v 30 amp electric dryer?

no. depending on length of run you'll need either 10 or 6 gauge wire for a 30 amp double pole breaker.


Can you use 14-3 wire to power metal halide light outside?

The question isn't what you're powering with a particular gauge of wire, but what's the current draw. If the metal halide light can run on a 15 Amp breaker (from the breaker panel), fine use your metal halide in your residential application and run it on the 14 gauge wire.


Can you run a 10 gauge wire 250 feet to the barn on a 120 amp breaker in the house If not what amp breaker should I use?

#10 cable is no good for 120 amps, you need #2 cable, and it can be used at a distance of 250 ft.


Can you hook a 15 amp and 20 amp breaker to a breaker box using 20 amp wire?

If the full load amps rating of the motor on the name plate is exactly 15 amps you need to use # 12 wire. If it is a longer run you may have to go up one more wire size. The breaker size you need is 30 amps.


240v nema6-50r outlet wired with 6 gauge wire and 50 amp breaker you need to run a heater with a nema 6-30p can you simply put a 30 amp receptical in place of the 50 amp receptical?

Not legally because the rating of the 30 amp receptacle would have a 50 amp breaker ahead of it. If you reduced the feed breaker to 30 amps and still use the #6 wire, this would be within the electrical code rules.


Can you run 14 gauge wire off 12 gauge 20 amp breaker?

You could if it fit properly in the connector, but it would be massive overkill since you only need 12 AWG wire. You also have to make sure the load can physically accommodate that larger size wire. Every so often someone will replace an electric cooktop witha gas one. All of the new gas cooktops require a 110v outlet. The old electric cooktop may have been run with a 50 amp breaker (and probably 6 gauge wire) In order to convert this 220 v circuit to a 110v circuit we change to a 20amp breaker. Depending upon the brand of breaker sometimes the wire will fit into it. If not, we splice on a short piece of 12 gauge wire and then connect to the breaker.