0
HIRE AN ELECTRICAL CONTRACTOR. If you're not an electrician and you're thinking you can put in a 1200 amp service yourself, you can't. If you need to ask how, you shouldn't even be thinking you can. This is a large job which needs to be completed by an electrical contractor. Period.
Add your answer:
Earn +20 pts
What size aluminum wire for 1200 amp service?
For Service Entrance Cable 600 kcmill (Thousands of circular mils).
What gauge wire for service entrance in Wisconsin?
Depends on the size of the service. 100 amp service will require 3 gauge, 150 amp service will require 1/0 gauge, and 200 amp service will require 3/0 gauge.
What is the minimum service size for a 225amp residential service?
A 200 amp service panel with a 60 amp sub-panel.
Do you need to change the wire size going from 100 amp service to 150 amp service?
Yes, the wire size has to be increased. The existing 100 amp service will now probably have a #3 conductor with an insulation factor of 75 or 90 degrees C which is rated for 100 and 105 amps respectively. Increasing to a 150 amp service will use a #1/0 wire size. If you are thinking of an upgrade, skip the 150 amp service and go to a 200 amp panel. New homes are installing 200 amp 42 circuit panels. The extra cost is only reflected in the materials as the labour costs will be the same regardless whether a 150 amp or a 200 amp panel is installed. The wire size for a 200 amp panel is #3/0. With an insulation factor of 75 or 90 degrees C the rating is 200 or 210 amps respectively.
Cost to install 1200 Amps Circuit Breaker?
1200 Amps is a huge breaker. Typical houses might have between 100 and 200 Amp service. Since this would have to be a very unique installation you would have to provide a lot more information before cost could be computed. You also have to indicate who is supplying the breaker which would be a significant cost on its own.
What size aluminum wire for 1200 amp service?
For Service Entrance Cable 600 kcmill (Thousands of circular mils).
For a parallel feed to a 1200 Amp service 3 phase what size is the grounding electrode to main service with 3 600 mcm parallel runs?
500 mcm
Can a 1200 watt amp give good bass to 2 kicker cvr 12's?
Yes, a 1200 watt amp can provide good bass for 2 Kicker CVR 12-inch subwoofers. Make sure to set the amp gain correctly, match the impedance of the subwoofers with the amp, and use a proper enclosure for optimal performance.
Can a 1200 watt amp power a 300 watt box?
Yes, a 1200 watt amp can power a 300 watt box. The wattage of the amp refers to its maximum power output, so it can deliver up to 1200 watts if needed. As long as the amp is set up properly and not pushed to its maximum capacity, it can safely power a 300 watt box.
Spl z2x-1200 1200 watt amp and two kdc-w3o11 1200 watt 12 in subs Can someone tell me the best configuration for wiring and settings on the side of the amp to give my subs the best power?
crutchfield has a wiring diagram for all kinds of configurations, check it out.
1200 watt wiring kit suitable for a 800 watt amp and 1100 watt sub not sure whether this would have a effect on the cables?
1200 Watt wiring is more than enough for an 800 Watt amp. The rating of the sub doesn't make any difference to the cables. If you want to use the sub to its rated power you should get a bigger amp. If the amp can only give out 800 Watts and the sub can take 1100 Watts then you can put a bigger amp on. It is still going to be loud as with an 800 Watt amp. I have a 300 watt amp with a 1200 Watt sub and people hear me coming.
Can you use a 1200 amp adapter for 500 amp appliance?
No, it is not recommended to use a 1200 amp adapter for a 500 amp appliance. The adapter should match or exceed the amp rating of the appliance to avoid damaging the appliance or creating a potential safety hazard. It is best to use an adapter that closely matches the amp rating of the appliance for optimal performance.
What gauge wire for service entrance in Wisconsin?
Depends on the size of the service. 100 amp service will require 3 gauge, 150 amp service will require 1/0 gauge, and 200 amp service will require 3/0 gauge.
What is the best way to hook up a single 12 inch dvc to a 1200 watt amp?
The best way to hook up a single 12 inch dvc to a 1200 watt amp is to use an MTX thunder box.
180 RMS is converted to how much watts?
Would be compared to 1200 watt amp
Can a 1200 watt amp power a 1300 watt sub?
It's actually a good idea to have a speaker that can handle higher wattage than the amp can produce.
Can you install 100 amp service in 200 amp meter base?
No, each size service needs its own meter base.
