answersLogoWhite

0

Depends on the breaker. If the load at the outlets is unknown then the standard rules of 80% apply.

You can only load a circuit 80% of it's maximum value. For instance, if you're connecting your GFCI outlets to a 15 amp breaker you can only have a maximum of 12 outlets.

If it's a 20 Amp breaker then you're allowed up to 16 outlets and so on.

In the US, you are limited to 13 receptacles on a 20 amp circuit and 10 receptacles on a 15 amp circuit in commercial or industrial installations. Any or all of these can be gfci-protected. You can install one gfci, the first one from the panel, and protect any or all the others from that one.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Electrical Engineering

Where is the GFI circuit breaker for all interior wall outlets located on 1993 Country Coach Magna RV?

In a 1993 Country Coach Magna RV, the GFI circuit breaker for all interior wall outlets is typically located in the bathroom or kitchen area, often near the sink. You may also find it in a central electrical panel or compartment. Check for a reset button on the outlet itself if it's a GFI outlet. If you have trouble locating it, consult the owner's manual for specific guidance.


What might cause low voltage at one outlet on a multioutlet circuit?

its an overload on the circuit breaker the 3 outlets are on.. many times groups of outlets are on different circuit breakers.. even though they are in the same room... especially if some are on a gfi outlet


How many eletrcal outlets can you have in a garage?

There is no limit as to the amount of circuits you can have in a garage. If you mean how many devices on a 15 amp single circuit breaker then the answer is 12. Be sure to total in light fixture outlets and switch boxes.


Can you back wire an outlet on a gfi circuit?

Don't know what you mean by back wire, but most GFCI outlets have a circuit to attach additional outlets that will be protected by the GFCI. Keep total load in minds.


Is a ground fault indicator outlet installed at the breaker box?

There are tow places to put a Ground Fault Circuit Interrupter. There is a GFCI breaker which would be installed in a breaker box and a GFCI outlet that can be installed anywhere. Most GFCI outlets allow you to connect regular outlets to the GFCI and those outlets will also be protected.

Related Questions

Plugging an electric heater into a GFI outlet caused the lights and other outlets to go out but didn't trip the circuit breaker why?

A GFCI receptacle can pass it's "protection" to other outlets wired from it. If the GFCI trips, all outlets wired from it will "trip" also. A GFCI tripping will not necessarily trip the circuit breaker in the service panel.


Does garbage disposals have a breaker?

Yes but the breaker would be at your electrical panel, they do not have a breaker connected to the garbage disposal but they do have a reset button on the bottom of the garbage disposal. Most modern homes also have a GFI outlet linked to the garbage disposal. If your disposal is tripping breakers or GFI outlets I would consider that something is very wrong with your disposal, or you installed one with to much power!


Do both the breakers and the outlets need to be GFI if you are running two 15 amp GFI circuits?

If you're using a GFCI breaker then the entire circuit will be protected by just the breaker alone. Every receptacle, switch, etc on that breaker will utilise the GFCI protection. You may have problems with it tripping if you plug in a motor (vacuum, etc) on the circuit.


What might cause low voltage at one outlet on a multioutlet circuit?

its an overload on the circuit breaker the 3 outlets are on.. many times groups of outlets are on different circuit breakers.. even though they are in the same room... especially if some are on a gfi outlet


If you install a 30A 240V GFI breaker will this be ok or will the cycles the dryer has prematurely fail the breaker?

Installing a 30A 240V GFI breaker for a dryer should be fine as long as the wiring and dryer itself are compatible with the breaker. The GFI breaker is designed to protect against electrical faults and should not be affected by the cycles of the dryer. Make sure to follow the installation instructions carefully to ensure proper functioning.


Why won't my GFI reset?

Your GFI may not reset due to a faulty GFI outlet, a tripped circuit breaker, a ground fault in the wiring, or a connected device causing the fault.


Can you have 3 gfi plugs in a bathroom on one breaker?

That's no problem.


How do you wire a GFI breaker?

To wire a GFI (Ground Fault Circuit Interrupter) breaker, first turn off the power to the circuit. Then, connect the hot wire to the breaker's terminal, the neutral wire to the neutral bar, and the ground wire to the ground bar. Finally, attach the breaker to the panel and turn the power back on.


How do you find a triped circuit?

Check the circuit panel / breaker box. The tripped breaker should be partway between 'OFF' and 'ON'. If nothing else, turn the breakers off then on, one at a time and when the tripped breaker is reset, the circuit should be live again. Also check GFI outlets. If one is in fault condition, it will need to be reset. If the tripped GFI outlet is protecting other outlets, they will come back when the tripped GFI is reset. These sockets seem to hide in many cases... Behind microwave ovens for example or refrigerators.


How many 115 volt outlets could you run from a 20 amp breaker?

If you never plug anything into them, there is no limit. If the total current drawn from all outlets exceeds 20 amps, the breaker will trip.


Why is my GFI plug not working?

Your GFI plug may not be working due to a tripped circuit, a faulty GFI outlet, or a wiring issue. Check the circuit breaker, reset the GFI outlet, and inspect the wiring to troubleshoot the problem. If the issue persists, consult a professional electrician for further assistance.


What is the solution for a refrigerator that is tripping the GFI?

When wiring a house, GFI plugs are strategically placed in areas that can be tripped by water. For example: in bathrooms, in garages, etc. There are certain areas that do not require GFI plugs. A refrigerator is one device that is usually on its own breaker and does not require a GFI plug. My recommendation is to locate where the refrigerator is. If it is in the house remove it and replace it with a non GFI plug.