A #1 copper conductor is rated at 140 amps with an insulation rating factor of 90 degrees C at 240 volt single phase, will give you a full 100 amps at 200 feet. #4 wire should give you 95 amps. Anything over 200 feet you will start loosing more amps.
i just left lowes an they told me to run 100 amp to my building i would need wire size 2-2-2-4 alumninum and run it in conduit the lowes around here does not sell copper wire that size
A #3 copper conductor with an insulation factor of 90 degrees C is rated at 115 amps. Even though the panel is rated at a higher amperage it is the main breaker that governs the wire size.
A 100-A sub-panel would be fed from a 100-A breaker.
For a 100 Amp breaker panel it would be 2 AWG. For 150 Amps it would require 2/0 (2 ought) aluminum wire.
Yes you do. The detached garage will either be fed with a single circuit or a sub panel. The wire feeding the garage will need to be protected and that is the purpose of the breaker (disconnect). The breaker size will be determined by the size of the wire that is used on this circuit.
i just left lowes an they told me to run 100 amp to my building i would need wire size 2-2-2-4 alumninum and run it in conduit the lowes around here does not sell copper wire that size
A #3 copper conductor with an insulation factor of 90 degrees C is rated at 115 amps. Even though the panel is rated at a higher amperage it is the main breaker that governs the wire size.
For a 100 amp service panel, typically a #8 copper wire or a #6 aluminum wire is recommended for grounding purposes. It's important to follow local electrical codes and regulations when selecting the correct size of the ground wire. It's always a good idea to consult with a licensed electrician for specific guidance based on your individual circumstances.
For a 100 amp panel 240 ft away, you would need to use 2 AWG aluminum wire to minimize voltage drop and ensure safe and efficient operation. It's important to consult with a licensed electrician to determine the exact specifications needed for your specific installation.
The wire size in a meter stack is governed by the size of the first over current device.
You can install a 100 amp sub panel off a 60 amp main panel fed by 100 amp service. This allows for the sub panel to be adequately powered with headroom for future circuits or expansions. It is important to ensure the wire size from the main panel to the sub panel is sufficient to handle the load.
#8 would be fine if you ground each panel separately to the ground rod
Yes, but at every reduction in wire size there has to be a breaker sized to the smaller wire size. The wire size for 100 amp panels is recommended at #3 copper conductor. From the 200 amp feeder panel you will require a 100 amp two pole breaker for each of the two 100 amp services. Keep in mind that if you run the 100 amp services close to maximum this will take away the capacity of the 200 amp service for other branch circuits coming off of it. Also keep in mind that if the panels are located, not in the same building as the 200 amp service that the 100 amp panels will be treated as separate services and will have to be constructed like a 100 amp service. This includes ground rods. Also the bonding screw will have to be removed that connects the neutral buss to the panel enclosure.
For a 100 amp sub panel located 250 ft from the main panel, you would typically need to use 3/0 aluminum wire or 2/0 copper wire to ensure efficient power transmission and voltage drop within acceptable limits. It is recommended to consult with a licensed electrician to ensure the appropriate wire size and materials are used for your specific setup.
A 100-A sub-panel would be fed from a 100-A breaker.
For a 100 Amp breaker panel it would be 2 AWG. For 150 Amps it would require 2/0 (2 ought) aluminum wire.
No, a 12 gauge wire is rated for 20 amps, which matches the breaker size. It is not recommended to use a wire that matches the breaker size as it can result in overheating and potentially cause a fire hazard. Consider using a thicker wire, such as 10 gauge, for the 20 amp breaker to ensure safety for the sub panel.