0
If you're installing a circuit that will contain receptacles in an industrial area and the first receptacle is more than 50 feet (15.24 meters) from the load center you should?
Wiki User
∙ 7y ago
Connect the circuit to the appropriate size circuit breaker to meet the required amperage of the circuit. Turn the breaker on and use the circuit. Unless the circuit is of a very high ampacity, plus 200 amps, don't worry about voltage drop over 50 feet.
Wiki User
∙ 7y ago
Add your answer:
Earn +20 pts
Why would receptacles have low voltage and the light switches no voltage on the same circuit?
lighting is usually on 15A breakers receptacles on 20A the probability is high that they are not on the same circuit. if they are the same circuit the probability is high that there hasn't been an electrical inspection
What is downstream in electrical?
The terminology down stream refers to an electrical circuit and where devices are connected into the circuit. In reference to the breaker that feeds the circuit everything is down stream from it. If a GFCI receptacle is added into the circuit as the first device, the GFCI can be wired to allow all of the regular receptacles to be protected down stream from that GFCI. Every device added to the circuit will be down stream from the one that is ahead of it. The only device that will not have something down stream from it will be the last device in the circuit.
No power in three wall receptacles. Replaced circuit breaker. Still no power. How to fix?
With electricity, once you have tried the circuit breakers, it is safest to get a qualified electrician to fix the problem......electricity is dangerous if you do not know what you are doing.
Can you replace an ungrounded circuit breaker with a GFCI circuit breaker?
Yes but it's redundant and may cause unnecessary "tripping" of the circuit. The GFCI circuit breaker is intended to protect an entire receptacle circuit whereas a GFCI receptacle is designed to protect only that receptacle and any which are provided power from its load side. (downstream)
How many 120VAC single-phase output receptacles does a 25kW Power Distribution panel have?
If you are referring to the 25KW Power Distribution Panel used by the military, NSN: 6110-01-244-3209, there are four 120VAC, 20A circuit breakers and four corresponding twist lock receptacles.
Does the NEC code allow multiple 20A receptacles on a 20A circuit Put another way does a 20A receptacle with T shaped neutral slots imply that no other outlets are that circuit?
The NEC allows multiple 20A receptacles on a 20A circuit. The T-shaped neutral slot on a 20A receptacle is designed to accommodate both 15A and 20A plugs, but it does not imply that no other outlets can be on the circuit. As long as the total connected load does not exceed the circuit's capacity, multiple receptacles can be connected.
Where must GFCI receptacles be installed in residential garages?
All receptacles in a garage must be GFCI protected by code. Typically, the first receptacle in the circuit (location is irrelevant) must be a GFCI, then all others down stream in the circuit will be protected, and can be common receptacles.
Can a 20 amp circuit breaker operate two 15 amp receptacle?
It is perfectly acceptable to have (2) 120 volt 15 amp receptacles operated from a 120 volt 20 amp circuit breaker (as a general rule of thumb 11 receptacles are acceptable on a 20 amp circuit). The 15 amp rating of the receptacle is the maximum allowed amperage that should be hooked up to the receptacle at any one time. So in this case the limiting factor is the amount of current being drawn across both receptacles simultaneously should not exceed the 20 amp rating of the circuit breaker. In the United States the NEC code allows the use of a 20 amp circuit breaker to feed a branch circuit consisting of 15 amp receptacles. Generally you would not exceed 11 receptacles though as you will assume an average load of 1.5 amps per receptacle and trying to maintain about 80% max load.
How is a plug in receptacle connected to other receptacles in a normal house circuit?
A plug-in receptacle is typically connected in parallel with other receptacles on the same circuit. This means that each receptacle is connected individually back to the circuit breaker or fuse box, allowing each one to be used independently without affecting the others. This parallel connection ensures that power can be distributed to multiple devices on the same circuit without overloading.
Can you control 10 outlets with one 20 amp GFCI outlet on one 20 amp circuit?
If each outlet draws less than 2 amps, then you could control 10 outlets with a 20 amp GFCI outlet on a 20 amp circuit. However, it's worth consulting an electrician to ensure the load calculations are accurate and the wiring is safe for the intended use.
Can duplex oulet have one dedicated outlet?
Answer for USA, Canada and countries running a 60 Hertz supply service.Yes, if it is connected with a three wire circuit such as kitchen counter receptacles. In this case both top and bottom of the duplex receptacle are dedicated circuits. An example of a duplex receptacle being the only device in the circuit from a 15 amp breaker is the receptacle for a microwave oven.
Are 15a receptacles ul rated for 20a?
No, 15A receptacles are not UL-rated for 20A circuits. It is important to use a receptacle that matches the rating of the circuit to ensure safety and prevent overloading.
How many electrical receptacles on 15 A breaker with 12 gauge wire?
In the United States and according to the NEC, in commercial and industrial installations, you are limited to 10 receptacles on a 15 amp circuit. The size of the wire is not a determining factor. There is no limit to the number of receptacles on a circuit in a home and there may be local codes where you live that have stricter requirements.
When installing an isolated circuit in a patient care area what color conductor is required to be terminated on the nickel-plated screw of a receptacle?
When installing and Isolated circuit, the orange-insulated conductor is required to be connected to the nickel-plated screw of recepticals
Why would someone use two positive wires to complete a house 2 plug receptacle circuit?
If the 2 hot wires are connected to either side of a receptacle, you have a 240v receptacle (assuming it's in the US). This is typically done for window air conditioners. But code requires that the receptacle have a different configuration than other receptacles in the building so you don't run the risk of plugging in a 120v device into a 240v receptacle.
DoesCode permit connecting receptacles to a 20ampere branch circuit using short lengths of 14AWG conductors as the pigtail between the receptacle terminals and the 12AWG branch-circuit conductors?
No. This practice is a violation of Article 210.19 (A) of the NEC. "Conductors of branch circuits supplying more than one receptacle for cord-and-plug-connected portable loads shall have an ampacity of not less than the rating of the branch circuit."
What are the different kinds of electrical receptacle?
The most common types are the regular type, where the only over current protection is provided by the breaker panel. the other most common type is the GFCI (Ground Fault Circuit Interrupter) This type has a built in "circuit breaker" so when it senses a fault in the circuit it trips-this type is the safest as they are more sensitive than circuit breakers in the breaker panel.See related links below.
