0
Volts by themselves are 0 amps. Volts cause current to flow, which is measured in amps. But there has to be a circuit, which is essentially a circle for the current to flow in. And current is usually limited by a load, which is any device that utilizes electrical energy. Without a load you have a short circuit which can allow hundreds or thousands of amps to flow until something burns up or a protective device trips, like a breaker or fuse.
Add your answer:
Earn +20 pts
600 thousandths equals how many tenths?
6
Six meters equals how many centimeters?
600
600 miles equals how many km per hour?
600 miles = 965.6 kilometers.
600 thousands equals how many tenths?
600 thousands equal 6,000,000 tenths,
How many 600 km equals miles?
If the question means how many miles is 600 km, the answer is 372.82 (to 2 dp).
0.8 megawatts 600 Volts equals how many amps?
To calculate the amperage, use the formula: Amps = Watts / Volts. In this case, 0.8 megawatts is equal to 800,000 watts. So, Amps = 800,000 watts / 600 volts, which equals approximately 1333.33 amps.
How many amps can handle in 12 volts a 600 volts 15 amps rated terminal bar?
The terminal strip's rating is 15 amps at 600 volts. It does not matter what the voltage is up to 600 volts, the maximum amperage allowed on the strip is 15 amps. It could be 15 amps at 12 volts or 15 amps at 600 volts or any voltage in between.
What is the conversion of 600 ma to amps?
A milliamp (mA) is a unit of electricity (600 mA equals .6 amps). Converted to volts 600 ma equals .6 volts
How many amps needed for a 600 watt floodlight?
If you are using a 120V power supply, a 600 watt floodlight will draw 5 amps of current (600 watts ÷ 120 volts = 5 amps). Remember to always check the specific electrical requirements of your floodlight to ensure the correct amperage.
How many amps does a 12 volt 600 watt transformer use at 120 volts?
A transformer does not use, it transforms voltage from one value to another. The output amperage is governed by the connected load. If the load wattage is higher than the wattage rating of the transformer then either the primary or secondary fuse will blow or the transformer will burn up if the fusing is of the wrong sizing. The maximum primary amperage can be found by using the following equation, Amps = Watts/Volts, A = W/E = 600/120 = 5 amps. The same equation is used for the calculating the maximum secondary amperage, A = W/E = 600/12 = 50 amps.
How many watts is 5 amps?
600 This depends on the voltage Voltage x Amps = Watts ex. At 120 volts 5 amps WILL BE 600 watts But at 110 Volts (Some house voltage), it will be 550 watts And at 277 Volt (commercial-Industrial Voltage), it would be 1385 Watts If you know Watts (Like a 75w Incandescent Lamp) and the Voltage: Watts / Volts = Amps So 75w / 120v = 0.625a The last would be Watts / Amps = Volts 600w / 5a = 120v
1 A microwave oven uses a 115 V electrical source and produces 600 Watts of power How many amps does it require?
To find the amperage, use the formula: Amps = Watts / Volts. In this case, 600 Watts / 115 Volts = approximately 5.22 Amps. So, the microwave oven requires approximately 5.22 Amps of current.
How many amps does a 3 phases 600 volt 10 hp draw?
Assuming the power factor is 1, a 10 hp motor operating at 600 volts in a three-phase system would draw approximately 13.33 amps.
How many volts is 2 gauge 200 amp 3 ohms?
To calculate the voltage drop in a circuit, you can use Ohm's Law (V = I * R). In this case, V = 200 amps * 3 ohms = 600 volts. This means that with a 200 amp current flowing through a 3 ohm 2-gauge wire, there will be a voltage drop of 600 volts.
A meter should indicate how many volts when connected to a 100 ohm resistor that has 6 amps of current passing through it?
600 VDC.
How many amps does a 600watt ballast pull?
Watts = Amps x Volts, so 600 W / 240 V = 2.5 A 600 W / 120 V = 5 A 600 W rated balast is more like 660 W in realty, so to be safe, plan for 3A pulled per ballast. P.S. New digital balasts are much closer to 600 W, something in 610 - 620 W range.
What is the power used by a 5 amps soldering iron at 120 volts?
The power used by a 5-amp soldering iron at 120 volts can be calculated using the formula: Power (W) = Current (A) x Voltage (V). With the given values, the power would be 600 watts (5 amps x 120 volts = 600 watts).
