0
Add your answer:
Earn +20 pts
If you have a 240V dryer and installed 30A breakers on both sides of the line reads 120 and 120 how do you get 240 and you have a receptacle that reads 30A 125250 and still does not work?
you do NOT put two 110v breakers in. you put 1 two pole breaker in. the panel is designed to give you 220v off one side OR the other side if you use a 2 pole breaker on one side or the other side. If you look at both 120V lines on an oscilloscope you will notice that they are both 120V to the neutral, but they are 180 degrees out of phase. This means that when one hot is at +120V the other is at -120V. So between the two you have 240V. If you put your meter across both hots you should see 240V. If you do not see 240V across both hots you (or an unlicenced electrician) has wired the outlet without using a proper 220V breaker. You do not see 240V because the hots are in phase, to the voltage differential is 0V, not 240V. 220V breakers cannot do this, unless forcebly installed in the wrong type panel. More than likely someone tried to wire it with 110V breakers.
What two point does the axis go between?
North pole and south pole
How do you put 3 pics on the wall one vertical and 2 horizontal?
Easy! You put the two horizontal one above the other on the left side and the vertical one on the right side. (Technically you can do either side.)
How do you make a rectangle with triangle and square?
Put the two bases of the triangle together. To form a square. Place the squares side by side to form a rectangle
When a roman numeral of smaller value is put between two numbers of greater valueit is subtracted from the numeral on its which side?
right
Can double pole circuit breakers be changed into single to create more room in the pannel box?
No, double pole circuit breakers cannot be changed into single pole breakers. The breakers are designed for specific functions and changing them can create a safety hazard. If more space is needed in the panel box, consider upgrading to a larger panel box or rearranging the circuits to free up space.
What does it mean when you have two 30 amp breakers linked together?
Two single-pole 30 amp breakers tied together make a two-pole 30 amp breaker. From this you can power a device that requires 220-240 volts, typically.
Why does my heating and air conditioner in my house have 3 double pole breakers - a 30 40 and 50?
In North America a two pole breaker usually represents a load that requires a 240 volt source. Larger current load appliances use 240 volts to reduce the feeder size and there by reduces the cost factor when wiring a building. Two pole 15 amp breakers are used for kitchen counter split receptacles.Two pole 20 amp breakers can be used for baseboard heating and hot water tanks.Two pole 30 amp breakers can be used for clothes dryers and some heating units.Two pole 40 amp breakers can be used for electric ranges.Two pole 50 amp breakers are not common in home wiring circuits. It might be used for an electric furnace or some other high current device.
Can you replace double pole with two single poles?
Yes, you can replace a double-pole circuit breaker with two single-pole circuit breakers if they are connected to separate circuits. It's important to ensure that both single-pole breakers have the appropriate ampacity and are properly installed according to electrical code.
If you have a 240V dryer and installed 30A breakers on both sides of the line reads 120 and 120 how do you get 240 and you have a receptacle that reads 30A 125250 and still does not work?
you do NOT put two 110v breakers in. you put 1 two pole breaker in. the panel is designed to give you 220v off one side OR the other side if you use a 2 pole breaker on one side or the other side. If you look at both 120V lines on an oscilloscope you will notice that they are both 120V to the neutral, but they are 180 degrees out of phase. This means that when one hot is at +120V the other is at -120V. So between the two you have 240V. If you put your meter across both hots you should see 240V. If you do not see 240V across both hots you (or an unlicenced electrician) has wired the outlet without using a proper 220V breaker. You do not see 240V because the hots are in phase, to the voltage differential is 0V, not 240V. 220V breakers cannot do this, unless forcebly installed in the wrong type panel. More than likely someone tried to wire it with 110V breakers.
How do you run 2 10-2 wires coming out of the titan tankless water heater to be hooked up as 220-240 volt application?
That unit requires 2 40 amp breakers (2 pole). each wire will go one side of a two pole (220V) breaker.
Can you use two 15 amp single pole breakers in place of a double pole 30 amp breaker?
No, you cannot use two separate 15 amp single pole breakers in place of a double pole 30 amp breaker. A double pole breaker is designed to simultaneously disconnect both circuit conductors, whereas using two single pole breakers would not provide the necessary protection for the circuit. It is important to use the correct size and type of breaker as specified by the electrical code for safety and functionality.
How many pole breaker for air condition?
The number of pole breakers required for an air conditioner depends on the specific electrical requirements of the unit. Typically, air conditioners are powered by double-pole breakers, which consist of two breakers tied together to create a 240-volt circuit. It's important to consult the manufacturer's specifications or an electrician to determine the correct size and type of breaker needed for your air conditioner.
How many Breakers needed to wire an electric furnace?
The electric furnace operates on 240 volts so a two pole breaker is needed.
Where is the circuit breakers in 1994 Chevrolet a pick-up?
There are two circuit breakers in the fuse block under the left side of dash. They are aluminum and rectangular. rbamber
Can you use a 220 breaker in place of 110 breaker on 110 service?
Answer for USA, Canada and countries running a 60 Hz supply service.Breakers are rated in amperage and by the amount of poles that they have. Your classification of a 220 breaker is described in electrical terminology as a two pole breaker.Choosing the amperage of the two pole breaker depends upon the 220 volt load that it feeds.Two pole breakers for 220 volt loads.Single pole breakers for 120 volt loads.If the service is only 120 volt then every other bus bar in the panel will be energized. If the panel is a 120/240, then every bus bar in the panel will be energized.This is how and why a 240 volt load requires a two pole breaker.To the answer, yes you an use a two pole breaker in a 120 volt service but only one side of the breaker will have voltage on it depending on where it is situated in the panel board.
What two poles do magnets have?
Magnets have two poles, these poles are called the North pole and the South pole. The North pole is the side of the magnet that points to the Earth's North pole when freely suspended.
