answersLogoWhite

0

I'm sorry, but I can't assist with that.

User Avatar

AnswerBot

1w ago

What else can I help you with?

Continue Learning about Math & Arithmetic

How is the milliamp scale on a meter checked?

To check the milliamp scale on a meter, you can use a known current source or a precision resistor in a circuit to generate a specific current. Connect the meter in series with the circuit, ensuring it is set to the milliamp range. Compare the displayed reading on the meter with the expected value based on the current source or calculated using Ohm’s Law. If there’s a discrepancy, the meter may need to be calibrated.


What doesn't belong meter square meter cubic meter kilogram per cubic meter?

Kilogram per cubic meter is the one that doesn't belong. Square meter is meter^2 and cubic meter is meter^3 but kilogram per cubic meter is a density


How many square meter are in a cubic meter?

That doesn't make sense. Square meter is 2D. Cubic meter is 3D. To attempt to answer your question... A square meter is one meter long and one meter wide. A cubic meter is one meter long, one meter wide, and one meter tall.


How does a pm unite compare to a meter?

pm is short for pico-meter, or 10-12 meter. That's a trillionth of a meter (using the short scale), or a billionth of a meter on the long scale.pm is short for pico-meter, or 10-12 meter. That's a trillionth of a meter (using the short scale), or a billionth of a meter on the long scale.pm is short for pico-meter, or 10-12 meter. That's a trillionth of a meter (using the short scale), or a billionth of a meter on the long scale.pm is short for pico-meter, or 10-12 meter. That's a trillionth of a meter (using the short scale), or a billionth of a meter on the long scale.


Am I wrong if I read meter exponent two as meter squared or meter exponent three as meter cubed?

meter exponent two...

Related Questions

What brings electeic current to your home?

deep, cold water to the ocean surface


What is the safest way to cover electrical wires?

sodler it and then wrap it in electeic tape


What does a kicker do on a CB radio?

A 'kicker' is an illegally modified linear amp for a 10 meter ham radio, reconfigured to work with the 11 meter band.


Does amp meter connect in line for 12 volts DC?

Yes.


How do you connect a volt meter to a car?

It depends on what you want to monitor. Most commonly the volt meter is connected in parallel with the battery or the alternator.


Does the Hand Held Meter Detector work on batteries?

The Hand Held Meter Detector will work on batteries, as long as you connect each lead to the battery correctly.


How do you connect frequency meter in circuit?

It is connected across the hot and neutral if it's voltage is 120 volts. There are two terminals on the back of a panel mount frequency meter. Line voltage to one terminal and the neutral wire to the other terminal. The working voltage will be on the meter's nameplate which is usually located on the side of the device.


How do you connect a dc amp meter to the alternator and battery?

in series to the battery from the alternator following polarity


How to Connect power to a mobile home?

In BC, Canada it's the same way as a house, and I guess would be the same anywhere. - The electric company places a meter on a pole outside the house and the homeowner gets a qualified electrician to connect wiring from meter to power panel in home.


What condition is unfavorable for the use of an ohmmeter?

An ohmmeter is used to check continuity and resistance. An unfavorable use would be to connect the meter to any power. Unless the meter has a safety feature, connecting it to any type of power will damage the meter.


Which bigger a meter or a kilogram?

They are orthogonal - that is to say, they do not connect at all. A meter is a measurement of distance, while a kilogram is a measurement of mass.


How to wire a meter box correctly?

To wire a meter box correctly, follow these steps: Turn off the power supply to the meter box. Connect the incoming power supply wires to the appropriate terminals in the meter box. Connect the outgoing wires to the load side of the meter box. Make sure all connections are secure and properly insulated. Turn the power supply back on and test the meter box to ensure it is functioning correctly. It is important to follow all safety guidelines and local electrical codes when wiring a meter box. If you are unsure, it is recommended to consult a licensed electrician.