0
What else can I help you with?
How many Cubic feet in 30 holes 5 inches deep and 10 in diameter?
V = volume of a cylinder = Pi*Diameter*depth 144 square inches = 1 square foot volume of each hole: Pi*10*5 ~= 157.1 square inches / 144 square inches/square foot = 1.091 square feet We have 30 such holes so total volume = 30*1.091 = 32.73 square feet.
What is the formula for pcd dia 100 for 8 holes?
The formula to calculate the Pitch Circle Diameter (PCD) for a given number of holes is: [ \text{PCD} = \frac{d}{\sin\left(\frac{180^\circ}{n}\right)} ] where ( d ) is the distance between holes (or the diameter of the circle on which the holes are located), and ( n ) is the number of holes. For a PCD of 100 mm with 8 holes, you would use this formula to determine the spacing and arrangement of the holes around the circle.
How much dirt is needed to fill a hole that is 15 ft X 3 ft?
Holes have three dimensions, except for cylindrical holes which only have two but one is a diameter. You only gave two dimensions and neither was designated a diameter In summary, you didn't give enough information to answer you question
What is the length and width of standard notebook paper?
Loose-leaf paper (three to five holes punched on the side so that it can fit in both 2-ring and 3-ring notebooks) usually measures 8.5 inches wide by 11 inches long.
How do you make a pair of nunchucks?
take a pice of pipe about 3 feet long and cut in into to pices of pipe in to 1 foot 6 inches and cut 2 holes in it and tie 2 nots one on each end in the rope after you put in the holes and now you should have a pair of nunchucks
How many cubic inches of grout needed to fill holes 4186 lineal feet at 1.25 in diameter?
Approx 246576 cubic inches.
What is the diameter of the holes on a golf course?
4 and a quarter inches.
How many Cubic feet in 30 holes 5 inches deep and 10 in diameter?
V = volume of a cylinder = Pi*Diameter*depth 144 square inches = 1 square foot volume of each hole: Pi*10*5 ~= 157.1 square inches / 144 square inches/square foot = 1.091 square feet We have 30 such holes so total volume = 30*1.091 = 32.73 square feet.
What makes small holes about 3 inches in diameter and about two inches deep all over the yard?
Skunks
What is the recommended 5 drill bit size for drilling holes in metal?
The recommended 5 drill bit size for drilling holes in metal is 0.2055 inches in diameter.
How you find the pcd of flange?
PCD (Pitch Circle Diameter) is the diameter of a circle that goes through each of the bolt holes. You can find it by measuring distance from centre of one bolt hole to the centre of opposite end bolt hole...
What are the standard toilet flange dimensions for proper installation?
The standard toilet flange dimensions for proper installation are typically 4 inches in diameter and have bolt holes that are spaced 3.5 inches apart.
What type of animal makes lots of holes in your yard that are about 2 to 3 inches in diameter in area next to woods where leaves were laying?
a gopher or a mole
What are the ideal dimensions for bird house holes to attract specific bird species?
The ideal dimensions for bird house holes to attract specific bird species vary depending on the species. Generally, smaller birds like chickadees prefer holes that are around 1-1.25 inches in diameter, while larger birds like bluebirds prefer holes that are around 1.5-1.75 inches in diameter. It is important to research the specific bird species you want to attract to determine the best hole size for their needs.
What causes Cone shaped holes in lawn 2-4 inches in diameter?
Sounds like a doodlebug www.antlionpit.com The armadillo leaves a hole just like this.
Are there black holes the size of stars?
The relevant magnitude is mainly the black holes' mass. Since black holes are the result of collapsing stars, yes, there are black holes with the mass of a star.The diameter is usually taken as the diameter of the event horizon. This diameter is directly proportional to the mass; a supermassive black hole such as Sag A* has a diameter comparable to that of a large star.
You want to drill three equadistant holes in a circle three inches in diameter?
simple option: take a string, wrap it around the tube, cut off extra, measure the string. Divide by 3, use a ruler to mark the 3 spots on the string, wrap back around tube, and transfer the dots to the tube. DRILL! Accurate option: find circumference of tube. (you can find this by measuring the diameter of the tube, multiply that by PI) divide by 3, mark a starting point, drill holes offset by your length.
