0
Assuming you need a metric ton, that's 1000 kilograms. To lift that, you need a FORCE of 9800 newtons. Force is related to pressure by: pressure = force / area, so the answer to the original question would depend, over what area the force is applied.
Add your answer:
Earn +20 pts
How many kg can one bar pressure lift?
This is a kind of trick question. In a closed static system containing fluid, pressure is equal everywhere. This is called the Law of Pascal. One can use this principle to lift a car with a finger. Fill a tank with water and have a car float on a platform. Now make a hole in the tank and connect a tube to it. By preventing the tube to leak, you have to apply a certain pressure, which may be smaller than 1 bar. If you increase the pressure, either by hand or possibly by blowing the tube, you can lift the car. Not so much with a short tube, but more with a long tube. The higher pressure in the tube will push the water back in the tank and cause the water in the tank to rise with the car on top of it.
How much is 1.00 in french money?
How much is one what - more information required
How much water is REQUIRED in one cubic meter of concrete?
12L
How strong is carnage?
carnage can lift 50tons and 2tons is the strength of a car so just imagin how many cars carnage could lift in one hand carnage can lift 50tones and venom can lift 80tons so imagin how many cars venom and carnage could lift in one hand
How much time is required to complete one cycle if the frequency is 120 Hz?
1/120 seconds!
How much hydraulic pressure is required to lift one ton load?
Hydraulic pressure required to lift a one ton load will depend on factors such as the size of the hydraulic cylinder, the mechanical advantage of the system, and frictional losses. As a rough estimate, for a simple hydraulic system with a one square inch piston and a one ton load (2000 pounds), you would need a pressure of 2000 psi to lift the load.
How does a wind lift?
Wind can lift objects by exerting force on them through pressure differences. When wind flows around an object, it creates an area of low pressure on one side and high pressure on the other. This pressure difference can generate lift, similar to how an airplane wing functions.
How much black powder lift charge required for 6 inch spherical arial shell?
Depending on the quality of bp you are using the general rule of thumb is one tenth the shells weight for a lift charge.
How much air pressure does it require to lift a car?
Any air pressure is sufficient, if you have enough area with that pressure applied. Foe example, you could lift a 10000 pound truck with 10000 psi, if you have one square inch being acted on; you could do it with 1 psi, if you had 69.5 square feet being acted on.
How does a hydraulic lift work?
A hydraulic lift works by having pressure travel through a tube into another. One tube is smaller forcing air into the larger one in order to push and raise the lift.
How much force is required to lift an 80 pounds 24 inch round hatch which is hinged on one side?
80 lbs until past 45 degrees
How much can Peyton Manning lift?
no one knows. He is too afraid to lift in front of anyone
How much force is used to lift 100 lbs using 3 pulleys?
Using 3 pulleys in a block and tackle system reduces the force required to lift an object by one-third. Therefore, to lift 100 lbs with 3 pulleys, you would need to apply approximately 33.33 lbs of force.
How much mmbtu is required to produce one ton of steam?
The amount of MMbtu required to produce one ton of steam can vary depending on the efficiency of the boiler and the pressure of the steam. On average, it takes about 10-12 MMbtu to produce one ton of steam at standard conditions.
What is the minimum force required to lift a 50-N load with one fixed pulley?
The minimum force required to lift a 50-N load using a single fixed pulley is 50 N. This is because a fixed pulley only changes the direction of the force applied, not the amount of force needed to lift the load.
How many kg can one bar pressure lift?
This is a kind of trick question. In a closed static system containing fluid, pressure is equal everywhere. This is called the Law of Pascal. One can use this principle to lift a car with a finger. Fill a tank with water and have a car float on a platform. Now make a hole in the tank and connect a tube to it. By preventing the tube to leak, you have to apply a certain pressure, which may be smaller than 1 bar. If you increase the pressure, either by hand or possibly by blowing the tube, you can lift the car. Not so much with a short tube, but more with a long tube. The higher pressure in the tube will push the water back in the tank and cause the water in the tank to rise with the car on top of it.
A fixed single pulley that is used to lift a block does what?
The choices are:A. Doubles the force required to lift the blockB. Decreases the force required to lift the blockC. Makes the block easier to lift by changing the direction of the force needed to lift it.D. Decreases the force required and changes the direction of the force required
