answersLogoWhite

0

What else can I help you with?

Related Questions

Why is heat needed to assist in dissolving polyvinyl alcohol?

Heat is needed to assist in dissolving polyvinyl alcohol because it increases the kinetic energy of the solvent molecules, allowing them to break the intermolecular forces holding the polymer chains together. This results in a faster and more thorough dissolution of the polyvinyl alcohol in the solvent.


How can I effectively remove adhesive from tile?

To effectively remove adhesive from tile, you can use a combination of heat, a solvent like rubbing alcohol or acetone, and a scraper or putty knife. Apply the solvent to the adhesive, let it sit for a few minutes, then gently scrape off the softened adhesive. Repeat as needed until the adhesive is completely removed.


Is iodine dissolve in turpentine?

No, iodine is not soluble in turpentine. Turpentine is a non-polar solvent, while iodine is a polar substance. To dissolve iodine, a polar solvent like alcohol or water is needed.


How can I effectively remove acrylic paint from plastic surfaces?

To effectively remove acrylic paint from plastic surfaces, you can use rubbing alcohol or acetone. Apply the solvent to a cloth and gently rub the paint until it starts to lift off. Repeat as needed until the paint is completely removed. Be sure to test the solvent on a small, inconspicuous area of the plastic first to ensure it doesn't damage the surface.


How do you mix lidocaine with rubbing alcohol and distilled water?

mix Lidocaine as 1 gram in 250cc which yields 4mg/cc, no alcohol needed to break it downmix Lidocaine as 1 gram in 250cc which yields 4mg/cc, no alcohol needed to break it downmix Lidocaine as 1 gram in 250cc which yields 4mg/cc, no alcohol needed to break it down


How do you clean liquid nails off of any surface?

To clean Liquid Nails off a surface, you can use a solvent like rubbing alcohol or acetone to soften the adhesive. Apply the solvent to a cloth and gently rub the area until the adhesive starts to loosen. Use a plastic scraper to remove the softened adhesive, being careful not to damage the surface. Repeat as needed until the adhesive is completely removed.


How can I effectively remove adhesive from wood floors?

To effectively remove adhesive from wood floors, you can use a combination of heat, solvent, and scraping. Start by heating the adhesive with a hairdryer or heat gun to soften it. Then, apply a solvent like rubbing alcohol or acetone to dissolve the adhesive. Use a scraper or putty knife to gently scrape off the softened adhesive. Repeat the process as needed until the adhesive is completely removed. Be sure to test the solvent in an inconspicuous area first to ensure it does not damage the wood.


How do you remove hair glue from clothing?

Most glues that are sold also has a solvent, check where you bought the glue and see if there is a solvent. Also you can try salt, olive oil, shampoo, and club soda mixed on the glue......let it sit for about 10 minutes then rinse out. Do this a couple of times to remove the stain.


Is evaporating rubbing alcohol on skin endothermic?

Water evaporation is an endothermic process.


How many ounces of 15 percent percent alcohol must be mixed with 23 percent alcohol solution to make 100 ounces?

Let x be the ounces of 15% alcohol solution. The amount of alcohol in the 15% solution is 0.15x, and the amount of alcohol in the 23% solution is 0.23(100 - x). Setting up the equation 0.15x + 0.23(100 - x) = 0.15(100) solves for x, which is approximately 38.5 ounces of the 15% alcohol solution needed.


How do you get black ink out of white carpet?

As soon as possible after the spill, grab a clean cloth and some rubbing alcohol. orSpray lubricant such as WD-40 or Triflow on the stain.Wipe the stain down with a sponge and warm soapy water.


How do you distill hand sanitizer in order to make edible alcohol?

Wikipedia has an article on Alcohol Rubs here: http://en.wikipedia.org/wiki/Hand_sanitizer They typically use ethanol (standard drinking alcohol mixed with something to render it undrinkable) or isopropanol ("rubbing alcohol" which is poisonous — not in a good way — if swallowed). A concentration of 60-70 percent is needed. Standard rubbing alcohol should do the trick, as would a 120+ proof liquor, although both will dry out your skin. You could mix in a small amount of glycerine for moisturizing, and possibly a thickener, but you risk diluting the alcohol to where the mixture is no longer effective. A mixture of nine parts 70% rubbing alcohol to one part glycerine should give you a good (but runny) substitute at a lower price.