0
Add your answer:
Earn +20 pts
What are the different modes of vi editor?
Command mode, and input mode. You switch between them using the ESC key.The two modes of 'vi' are input mode, and command mode. In input mode all you can do is insert text, and in command mode you can make editing changes to existing text (by issuing commands).Switching between the modes is accomplished by pressing the ESC (escape) key.
What is pi mode operation in tunable magnetron?
because pie mode has maximum of its output efficent and is mostly used mode in the case of magnetron
How does the mean relate to the mode?
There is no direct relationship between the mean and mode.
What does the outlier affect the most out of mean median and mode?
The mean. Or the mode.
What is the mean of 5 and mode of 4?
There is not much point in calculating the mean or mode of a single number. The mean of 5 is 5. The mode of 4 is 4.
What is invertion?
An inverting amplifier is one where the output is an inverted function of the input. The Class A transistor amplifier, also known as common-emitter, is inverting. As you increase the voltage on the base, the output voltage on the collector decreases. The operational amplifier has an inverting and a non-inverting input. In typical bridge mode, the output is inverted with respect to the (inverting) input, and the non-inverting input is used to reject common-mode input signals by moving the virtual ground point as needed.
What are the two methods that a hard drive uses to transfer data between itself and memory?
DMA (direct memory access) transfer mode or PIO (programmed input/output) transfer mode
Why won't your 1993 Dodge Intrepid shift out of second gear?
Transmission is in limp mode and most likely it is the input or output sensor or a wiring problem to one of them.
Who created Limited Access Mode in WikiAnwers?
The creators of the website. It's a concept found on almost every single website that has users that produce input and output.
Define what is meant by a common-mode input signal?
Common mode input signal is a term associated with Differential amplifiers.There would be two input signals in a diff. amplifier.The common component of these two signals is called common mode input signal.ie.if V1 and V2 are the two input signals then (v1+V2)/2 is the common mode input signal.Also |v1-v2| is the difference mode input signal.
What does cmmr mean?
Do you mean CMRR? If so, it means Common Mode Rejection Ratio. CMRR measures how well a differential input will reject a common mode signal (common mode means the same signal applied to both differential input leads at the same time). The ratio is expressed in decibels (dB).
What is the difference between nonlinear devices and linear devices?
In saturation region transistor acts as a non linear device i.e, there is no linear relation between input and output because in saturation region output does not change for variation in input. Whereas in other operating mode transistor acts as a linear device.
What is input mode in computer graphics?
request mode,sample mode and event mode
What is Sink and source mode of transistor?
Source mode at output provides safety than sink at output
What is the effect of the op amp in the circuit?
So long as you remain with the range of the device (power supply rails less a volt or two), the output of an op-amp will go to what ever value is required to maintain the input stages (bridge) to remain the same. So, the effect on input voltage on output of an op-amp is dependent on the feedback circuit.
What is clocked-mode sequential circuit?
A sequential circuit is a type of logic circuit. It sends an output that is dependent upon the present input in addition to the history of the input. That makes it different from a combinational circuit, whose output depends solely on the present input. Given their reliance on input history (or stored input), sequential circuits are particularly useful in computer random access memory (RAM). The two types of sequential circuits are synchronous circuits and asynchronous circuits.
Is transistor linear or non linear?
A transistor can function in both linear and non-linear modes. In the linear mode, it can amplify small signals with a linear relationship between input and output. In the non-linear mode, the transistor operates as a switch, turning on or off based on the input signal.
