0
As we mentioned earlier, a CRT can be used to graphically and visually plot an electronic signal,such as a sine wave. This is done by using a second set of deflection plates called VERTICAL-DEFLECTION PLATES
Norwood Mayert
Add your answer:
Earn +20 pts
Monitor got hit now there are vertical lines?
Line deflection has been lost most likely the CRT if this is as a result of physical injury or the line timebase in the case of an electrical fault.
What is a zero deflection?
A zero deflection is the adjustment of a sight, parallel to the axis of the bore of the gun to which it is attached.
Why is the graph between load and deflection a straight line?
Because load and deflection are directly proportional to each other
How to find curve length when deflection angle know?
the curve length L is equal to 100 * delta angle/2 but if you only know the deflection angle then use R = 5729.58/ Deflection angle (in degrees) and once you have you find a way around it lol
Exactly vertical or perpendicular?
There is no such thing as exactly vertical because either it is vertical or it is not. You cannot have approximately vertical - it is not vertical, then. Vertical means at 90 degrees to the horizon (or horizontal).
What is vertical deflection plate?
As we mentioned earlier, a CRT can be used to graphically and visually plot an electronic signal,such as a sine wave. This is done by using a second set of deflection plates called VERTICAL-DEFLECTION PLATES
What causes just a thin flat line and nothing else to appear on your tv screen?
The vertical deflection system is broken. The vertical deflection system is broken.
What does it cost to repair the vertical deflection system on a television?
$200.00
Working of vertical deflection plates in CRO?
Baba ji ka thullu?
What is called the winding around the CRT yoke that deflects the electron beam with its magnetic field?
It's called a deflection coil. If a c.r.t. uses magnetic deflection, there will be two deflection coils, a horizontal one and a vertical one.
What has the author Joseph Evans Bennett written?
Joseph Evans Bennett has written: 'The determination of the astro-geodetic deflection of the vertical'
How do you fix my RCA TV when all i get for video is a single white horizontal line?
This issue could be due to a faulty vertical deflection circuit or a problem with the IC which controls the vertical deflection. Check for loose connections and broken components in the vertical circuit. If you're not experienced in electronics repair, it's best to consult a professional technician to diagnose and fix the issue.
What is horizontal and vertical amplifier in cathode ray oscilloscope?
The horizontal and vertical amplifier in the cathode-ray oscilloscope are deflection plates. The horizontal amplifier causes the beam to be deflected horizontally at a rate that is uniform. The vertical amplifier causes the beam to deflect vertically.
What is difference between settlement and deflection?
Settlement refers to vertical movement of a structure's foundation or ground whereas deflection is the bending or curvature of a structural element like a beam or slab under load. Settlement is a downward movement while deflection is a lateral or horizontal displacement.
What is the unit of deflection sensitivity of cro?
The unit of deflection sensitivity of a Cathode Ray Oscilloscope (CRO) is volts per division on the vertical axis of the screen. It represents how much voltage change is needed to move the electron beam by one division vertically on the screen.
What is the purpose of camber in steel beam?
Camber is the amount of deflection provided in the opposite direction of loadings. That is when the beam is subjected to Vertical downward loadings, the beam has a tendency of deflecting downwards. In this case, camber value is to be given in the upward direction so that when it is fully loaded condition, the beam would have almost zero deflection. Similarly, when the beam is subjected to vertical upward loadings, the camber value is to be given in downward direction. The purpose of camber in steel beam is to have almost zero deflection w.r.t.o beam axis after loading of beam as highlighted earlier. by R.Ravichandran, Chennai-49
What is the deflection sensitivity of a cathode ray oscilloscope?
It is the deflection on the screen (meter) per volt of deflection
