0
Add your answer:
Earn +20 pts
How much water is in 100 feet 1.75 inch hose?
There need not be any water at all in the hose! The capacity of the hose is 1.67 cubic feet.
How much water in a foot of 5 inch hose?
1 Gallon
How much water does a 3 inch hose hold?
you need more info than that. you will need to provide the length of the hose and the inside diameter of the hose to calculate the amount of water it will hold
How long would it take to fill a gallon jug with a one eighth of an inch hose?
It depends on the flow rate in the hose and that depends on the water pressure.
How much does a 100 ft section of 5 inch in diameter fire hose weigh with water?
It is an accepted fire service understanding that 5" Large Diameter Hose (LDH) will hold 1 gallon/ft. On average a 100' section of 5" empty weighs 110 lbs. With water weighing 8.33 lbs/gal. a 100' section of LDH filled with water will weigh approximately 944 lbs.
What is the critical velocity of 2.5 inch fire hose?
300 GPM
What is critical velocity for 3 inch hose?
The critical velocity for a 3-inch hose depends on the fluid flowing through it. In general, critical velocity is the velocity at which the flow changes from laminar to turbulent. It can be calculated using the Reynolds number for the specific fluid and hose diameter.
Which as more resistance a garden hose or a fire?
Difficult to say. Hydraulic resistance is proportional to diameter as well as length and velocity. Water moving very slowly in a short length of either type of hose would have negligible resistance. The more likely answer you want is that high-velocity water in a garden hose would experience MUCH more resistance (friction loss) than that in any fire hose of larger diameter. The actual numbers will depend upon specific friction-loss factors, including the type and size of hose and the gallons per minute. For example, the friction loss coefficient in a 1.5-inch fire hose (24) is more than ten times what it would be in a 2.5-inch hose (2.0) and 100 times that of a 4-inch hose (0.2).
Weight of 50 ft section of 3 inch fire hose?
Weight of 50ft section of 3 inch hose with water in it?
How many gallons of water to fill a 2 inch fire hose?
A standard fire hose is 50 feet long. A hose this length with a 2-inch radius grants about 4.36 cubic feet. This volume holds 32 gallons of water.
How many gallons of water is in a 2.5 inch fire hose fifty feet long?
A 2.5 inch fire hose has a capacity of approximately 60 gallons per 100 ft. Therefore, a 50 ft hose would hold around 30 gallons of water.
How much does a 50 ft section of 5 inch diameter fire hose weight?
109 lbs with no water
How much does 100 ft of 4 inch fire hose weigh?
100 pounds with couplings, 68 without.
A two inch hose carries two times the volume of a one inch hose.?
All else being equal, a 2-inch hose carries 4 times the volume as a 1-inch hose.
How much supply hose does NFPA recommend pumpers carry?
NFPA 1901, Standard for Automotive Fire Apparatus - Requires pumpers to carry: * 15 feet of large soft sleeve hose or 20 feet of hard suction hose * 1200 feet of 2 ½ inch or larger supply hose * 400 feet of 1 ½ , 1 ¾, or 2 inch attack hose
How much does a 100 ft section of 6 inch fire hose hold?
If "6 inch" is the inside diameter of the hose, thenVolume = (pi) (radius)2 (length) = (pi) (3)2 (1,200) = 33,929.2 cubic inches = 146.88 gallons (rounded)
How much does a 100 ft section of 2.5 inch in diameter fire hose weigh with water?
That section of hose holds 25.5 gallons of water when it's full, which weighs about 213 pounds. To that, add the weight of the empty hose, which I don't know.
