answersLogoWhite

0

The safe working load can be calculated using the 6 x 19 &. 6 x 36 classification.

User Avatar

Wiki User

11y ago

What else can I help you with?

Continue Learning about Math & Arithmetic

A wire rope sling with a strength of 10000 pounds and a total working load of 2000 pounds has a design factor of what?

5


If piece of rope is wound around a cylinder pipe 18 times. if the diameter of the pipe is 600 mm how long is the rope?

To find the length of the rope wound around the cylinder, calculate the circumference of the pipe first. The circumference ( C ) is given by the formula ( C = \pi \times d ), where ( d ) is the diameter. For a pipe with a diameter of 600 mm, the circumference is approximately ( C = \pi \times 600 \approx 1884.96 ) mm. Since the rope is wound around the pipe 18 times, the total length of the rope is ( 18 \times 1884.96 \approx 33,999.28 ) mm, or about 34 meters.


Why is three strand rope stronger than four or more strands of the same diameter?

Whoever told you this is whacky. Why would you think this is true?


The meaning of rope vs line?

Line is a nautical term for a rope. But a rope can be a line attached on only one end in normal use. The bell rope, the bucket rope, the tiller rope, the bolt rope, check rope, foot rope, monkey rope, and the dip rope.


How do you get most the most area with 4 meter rope?

The maximum area that you can contain with a 4-meter rope is a circle with a diameter of 4/π meters and an area of 4/π square meters, or about 1.273 square meters. If you use the rope to make an equilateral triangle with sides of 4/3 meter, you get an area of (4/9)(√3) or 0.770 square meters. If you use the rope to make a square with sides of 1 meter, you get an area of 1.000 square meter. If you make a polygon with more sides, the area bounded by your 4-meter rope will increase, approaching the limit of 4/π as the number of sides increases.

Related Questions

Safe working load calculation for flexible wire rope?

To calculate the safe working load for a flexible wire rope, you need to consider factors such as the diameter of the rope, the material it is made of, the construction (number of strands and wires per strand), and the type of load (static or dynamic). The safe working load is typically specified as a percentage of the breaking strength of the wire rope, with industry standards recommending values ranging from 5% to 20% of the breaking strength depending on the application and safety factors. It is important to follow manufacturer guidelines and consult relevant standards when calculating the safe working load for a wire rope.


How do you calculate SWL?

TO CALCULATE THE SWL OF LIFTING WIRE ROPE THE FORMULAE CAN BE USED- 8*D2 WHERE 'D' IS THE DIAMETER OF WIRE ROPE IN 'mm' THIS WILL GIVE THE APPROX SWL (SAFE WORKING LOAD CAPACITY)


What is the weight per meter for 32mm 6x29FI IWRC steel wire rope?

The weight per meter for a 32mm 6x29FI IWRC steel wire rope is approximately 9.47 kilograms per meter. This figure may vary slightly depending on the specific manufacturer or tolerances. It is important to consult the manufacturer's specifications for precise measurements.


A wire rope sling with a strength of 10000 pounds and a total working load of 2000 pounds has a design factor of what?

5


How do i calculate nominal breaking strength of wire rope?

These are rule of thumb formulas but close to a manufacture's chart. for fiber core wire rope square the diameter times 42 = NBS Example, 1/2" x 1/2" x 42 = 10.5 tons UBS (Ultimate breaking strength) or NBS The formula is the same for IWRC, but use 45 as the multiplier, because of the higher strength in the rope. Example, 1/2" x 1/2" x 45 = 11.25 ton


What is the design factor of a wire rope sling with a strength of 10000 pounds and a total working load of 2000 pounds?

a multiplier of 5


Is safe working load of rope same as breaking strain?

To convert breaking strain to safe working load you must establish a safety factor (SF). Assume SF of 10. If a line has a breaking strain of 1 tonne then you should only suspend or load the line to a strain of 100Kg (1000Kg/10) A common SF for normal use is 6. If human loads are in use then SF 10 is more common.


What is wire rope minimum breaking load?

The minimum breaking load of a wire rope refers to the minimum load required to break the rope under laboratory conditions. It is important to consider this specification when selecting a wire rope for lifting or pulling applications to ensure safety and optimal performance. The minimum breaking load is typically expressed in tons, pounds, or kilograms depending on the standard used.


What is tensile load?

Think of a tensile load as a "pulling" force. A tensile load is the only type of load that can be taken by a rope, for instance.


How calculate wire rope load capacity?

Wire rope load capacity can be calculated by considering factors such as the breaking strength of the wire rope, the design factor for the specific application, and any additional safety factors required. The formula typically used is: Load capacity = (Wire rope breaking strength / Design factor) - Weight of the load. It is crucial to consult industry standards and guidelines when determining load capacity to ensure safety and reliability.


Where is the load arm on a pulley?

The load arm is the radius of the pulley. This is the distance from the fulcrum to the load-carrying side of the rope.


SWL for 10mm diameter wire rope?

1.4-ton