0
What else can I help you with?
How do you add another porch light to an existing switch?
Piggyback off the box for the existing light. Run a wire from the existing junction box to a new junction box (which is placed wherever you want the new fixture). Then, in the existing box, connect the wire coming from the switch, the wire for the existing fixture, and the wire for the new fixture together using wire nuts. Wire up the new fixture, and presto, you have two fixtures on a switch where there was only one before.
Can you connect a wall switch and a light fixture to an existing light fixture?
If the question is, can I wire a switch to an existing light fixture (and I must assume that it's something like a pull-chain light fixture), the answer is yes.If the question is, "how do I wire a switch to an existing light fixture that has no external switch", the answer is, "in series".The attached web site gives simple instructions on how to wire a basic light switch to an existing light.See sources and related links below
Can you extend power through a 3 wire switch leg for a half switched outlet to a new switch for a new light?
Yes, you can extend power through the 3-wire switch leg to a new switch for a new light. You would need to connect the hot wire to the common terminal on the existing switch, then extend the hot wire to the new switch, along with the traveler wire. At the new switch, connect the hot wire to the common terminal and the traveler wire to one of the traveler terminals.
How do you wire an additional light to another light with a switch?
In the wall switch box you should have a white and black pair from your source of power (120 volts). The other pair of black and white wires from the wall box should be going to the light fixture junction box. With the power off, connect the two white wires together with a wire nut. Connect the two bare copper ground wires together making sure that at least one of the ground wires goes under the green screw in the switch junction box. Turn the switch to the off position, no little indicator bump showing on the switch toggle lever. Now take the black incoming hot wire and put it under the top screw on the switch. Hot wires always go to the top of switches. Now put the black wire that is going to the light fixture under the bottom screw. Tighten both. Install the switch into the wall box with the switch handle in the down position. All switches when installed must be off in the down position. Install the switch plate cover.
How do you wire a light and switch with the 2 wire old romex?
To wire a light and switch using 2-wire Romex, connect the black wire to the brass screw on the switch, the white wire to the light fixture, and the white wire to the silver screw on the switch. Make sure to cap the unused wire at both ends for safety. Be sure to turn off the power before starting and consult a professional if you are unsure.
How do you add another porch light to an existing switch?
Piggyback off the box for the existing light. Run a wire from the existing junction box to a new junction box (which is placed wherever you want the new fixture). Then, in the existing box, connect the wire coming from the switch, the wire for the existing fixture, and the wire for the new fixture together using wire nuts. Wire up the new fixture, and presto, you have two fixtures on a switch where there was only one before.
Can you connect a wall switch and a light fixture to an existing light fixture?
If the question is, can I wire a switch to an existing light fixture (and I must assume that it's something like a pull-chain light fixture), the answer is yes.If the question is, "how do I wire a switch to an existing light fixture that has no external switch", the answer is, "in series".The attached web site gives simple instructions on how to wire a basic light switch to an existing light.See sources and related links below
How do you hook up a light and switch from an existing light?
Add a light to switch from a different circuitI think here your concern is that you don't want change the performance of the circuit to which you add the light.so you have to use a relay or a solid state relay to the circuit and a separate power supply to the light in compliance with all the safety rules.
How can I wire a light switch to a light?
To wire a light switch to a light, you will need to connect the switch to the power source and the light fixture. Turn off the power, remove the cover plate, and disconnect the existing switch. Connect the wires from the switch to the corresponding wires in the wall and the light fixture. Secure the connections with wire nuts and screw the switch back into place. Turn the power back on and test the switch to ensure it is working properly.
How do I wire a light switch to a light?
To wire a light switch to a light, first turn off the power to the circuit. Connect the black wire from the switch to the black wire from the light. Connect the white wire from the switch to the white wire from the light. Finally, connect the ground wire from the switch to the ground wire from the light. Secure all connections with wire nuts and cover with electrical tape. Turn the power back on and test the switch to ensure it is working properly.
Can you extend power through a 3 wire switch leg for a half switched outlet to a new switch for a new light?
Yes, you can extend power through the 3-wire switch leg to a new switch for a new light. You would need to connect the hot wire to the common terminal on the existing switch, then extend the hot wire to the new switch, along with the traveler wire. At the new switch, connect the hot wire to the common terminal and the traveler wire to one of the traveler terminals.
How do you wire a dimmer switch to a light?
To wire a dimmer switch to a light, first turn off the power to the circuit. Remove the existing switch and connect the dimmer's wires to the corresponding wires in the electrical box. Typically, the black wire is connected to the hot wire, the green wire to the ground wire, and the red or white wire to the load wire. Secure the connections with wire nuts and install the dimmer switch into the electrical box. Turn the power back on and test the dimmer switch to ensure it is working properly.
What is the wiring diagram for a 4 wire light switch?
A 4-wire light switch typically includes a ground wire, a hot wire, a neutral wire, and a traveler wire. The wiring diagram for a 4-wire light switch will show how these wires are connected to the switch terminals to control the light fixture.
How should I properly wire a dimmer light switch in my home?
To properly wire a dimmer light switch in your home, first turn off the power to the circuit at the breaker box. Remove the existing switch and connect the dimmer switch following the manufacturer's instructions. Typically, you will connect the hot wire to the black wire on the dimmer switch, the neutral wire to the white wire, and the ground wire to the green or bare wire. Secure the wires with wire nuts and install the dimmer switch into the electrical box. Turn the power back on and test the dimmer switch to ensure it is working correctly.
How can I properly install and wire a 4 way light switch in my home?
To properly install and wire a 4-way light switch in your home, you will need to first turn off the power to the circuit. Then, remove the existing switch and identify the common wire. Connect the common wire to the common terminal on the new 4-way switch. Next, connect the traveler wires to the traveler terminals on the switch. Finally, connect the ground wire to the ground terminal. Secure the switch in place and turn the power back on to test the switch.
How do you wire an additional light to another light with a switch?
In the wall switch box you should have a white and black pair from your source of power (120 volts). The other pair of black and white wires from the wall box should be going to the light fixture junction box. With the power off, connect the two white wires together with a wire nut. Connect the two bare copper ground wires together making sure that at least one of the ground wires goes under the green screw in the switch junction box. Turn the switch to the off position, no little indicator bump showing on the switch toggle lever. Now take the black incoming hot wire and put it under the top screw on the switch. Hot wires always go to the top of switches. Now put the black wire that is going to the light fixture under the bottom screw. Tighten both. Install the switch into the wall box with the switch handle in the down position. All switches when installed must be off in the down position. Install the switch plate cover.
How can I properly hook up a light switch in my home?
To properly hook up a light switch in your home, follow these steps: Turn off the power to the circuit at the breaker box. Remove the cover plate and existing switch. Connect the black wire from the power source to the black wire on the switch. Connect the white wire from the power source to the white wire on the switch. Connect the ground wire to the green screw on the switch. Secure the switch in place and replace the cover plate. Turn the power back on and test the switch to ensure it is working properly.
