answersLogoWhite

0

If there is nothing else on the circuit then you could easily install 15. If there are outlets on the same circuit then try and keep the total of outlets and lights to a maximum of 15. But in reality the number of devices depends on how many amps each device pulls. Add up the amperage of the recessed lights you are going to install and then add any outlets and what may be plugged into them to get the number you can install. A 100 watt light bulb will draw about 1 amp. So you can easily have 15 on a 20 amp circuit.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Natural Sciences

How many floodlights can you connect on a 10a circuit breaker on a 220 voltage supply?

To answer this question the wattage of the flood lights must be stated.


Why do some lights go off in your house when you turn on too many appliances?

In a well designed house the lights are not connected to the same circuit as an appliance. If by going out you are saying that a breaker trips, then your appliances and lights combined are exceeding the rating of the breaker. You either need to rewire and balance the loads better or plug high current appliances into different outlets on another breaker. If you are not tripping breakers, but lights are just dimming you have a bigger problem with inadequate current supplying your house.


How many outlets and lights on a 60 amp breaker?

It is recommended to have a maximum of 8 to 10 outlets and lights combined on a 60 amp breaker depending on the power draw of the devices connected. It is important not to overload the circuit to prevent potential hazards such as electrical fires. It is advisable to consult with a qualified electrician to ensure the load on the circuit is within a safe limit.


When you turn the house lights on the breaker blows why?

Ok, lets assume that these are not newly installed lights or lights added to this already existing circuit first what type of lights are they? the reason I asked is because if they are fluorescent lights it could be a faulty ballast. if it's regular light bulbs then they are several things to look for. how many lights on this breaker? have you placed a higher wattage bulb in these lights than recommended? what is your combined wattage? a 15 amp breaker is rated to supply power safely up to a maximum of 1440 watts. add up the wattage of each light bulb including any outside flood lights or outlets also on this circuit. If the the total is under 1440 watts then first replace the breaker with the same wattage rating then turn each light one at a time and wait to see if the breaker trips again. If it does, check the last light you switched on. Answer for USA: Never load a breaker to its full rating. The law allows only 80 percent of the breaker rating. That's the 1440 watts for a 15 amp breaker, and 1920 watts for a 20 amp breaker. Also look for a load you might not think is on the breaker, such as an outdoor light, or something in a hall or another room. Other causes: - A motor draws more current when it starts than when it runs. - An aging breaker, or one that has been overloaded too many times, can trip at a reduced current. If this is the case, it needs to be replaced.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any workANDalways use an electricians test meter having metal-tipped probes(not a simple proximity voltage indicator)to insure the circuit is, in fact, de-energized.


How many canned lights can go on one breaker?

The number of can lights that can go on one breaker will depend on the wattage of each light and the maximum load capacity of the breaker. It's important to calculate the total wattage of all the lights and ensure it does not exceed the amp rating of the breaker to avoid overloading it. Consult with an electrician to determine the appropriate number of can lights that can safely go on one breaker.

Related Questions

How many recessed lights in kitchen?

Well, it depends on the size of your kitchen and the watt of the recessed light. But I think if you choose LED recessed you don't have to own many of them. For my kitchen, I only use 6 of LED recessed lights.


How many 1.2 amp lights can a 20 amp breaker hold?

No more than 13 maximum on a 20 amp circuit.


How many floodlights can you connect on a 10a circuit breaker on a 220 voltage supply?

To answer this question the wattage of the flood lights must be stated.


How many recessed lights should be installed in a room for optimal lighting?

The number of recessed lights needed for optimal lighting in a room depends on the size and layout of the room. As a general guideline, it is recommended to space recessed lights about 4-6 feet apart for even lighting distribution.


Why do some lights go off in your house when you turn on too many appliances?

In a well designed house the lights are not connected to the same circuit as an appliance. If by going out you are saying that a breaker trips, then your appliances and lights combined are exceeding the rating of the breaker. You either need to rewire and balance the loads better or plug high current appliances into different outlets on another breaker. If you are not tripping breakers, but lights are just dimming you have a bigger problem with inadequate current supplying your house.


Why is the circuit breaker tripping?

The circuit breaker is tripping because there is an overload of electrical current flowing through the circuit, which can be caused by too many devices plugged in or a short circuit.


How many ampacity rating do a circuit breaker need for the general purpose circuit?

Usually a 15 or 20 amp breaker is sufficient


How many outlets and lights on a 60 amp breaker?

It is recommended to have a maximum of 8 to 10 outlets and lights combined on a 60 amp breaker depending on the power draw of the devices connected. It is important not to overload the circuit to prevent potential hazards such as electrical fires. It is advisable to consult with a qualified electrician to ensure the load on the circuit is within a safe limit.


Recessed Lighting?

form_title= Recessed Lighting form_header= Brighten up your home with recessed lighting. Do you currently have recessed lights?*= () Yes () No How many rooms do you want recessed lights installed?*= {1, 2, 3, 4, 5, More than 5} When do you want this project completed?*= _ [50]


How many recessed lights are needed in a 14 X 14 room?

That depends on the usage of the room and the recessed lights you have selected. Some rooms, like bathrooms, need more light while others, like closets do not.


When you turn the house lights on the breaker blows why?

Ok, lets assume that these are not newly installed lights or lights added to this already existing circuit first what type of lights are they? the reason I asked is because if they are fluorescent lights it could be a faulty ballast. if it's regular light bulbs then they are several things to look for. how many lights on this breaker? have you placed a higher wattage bulb in these lights than recommended? what is your combined wattage? a 15 amp breaker is rated to supply power safely up to a maximum of 1440 watts. add up the wattage of each light bulb including any outside flood lights or outlets also on this circuit. If the the total is under 1440 watts then first replace the breaker with the same wattage rating then turn each light one at a time and wait to see if the breaker trips again. If it does, check the last light you switched on. Answer for USA: Never load a breaker to its full rating. The law allows only 80 percent of the breaker rating. That's the 1440 watts for a 15 amp breaker, and 1920 watts for a 20 amp breaker. Also look for a load you might not think is on the breaker, such as an outdoor light, or something in a hall or another room. Other causes: - A motor draws more current when it starts than when it runs. - An aging breaker, or one that has been overloaded too many times, can trip at a reduced current. If this is the case, it needs to be replaced.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any workANDalways use an electricians test meter having metal-tipped probes(not a simple proximity voltage indicator)to insure the circuit is, in fact, de-energized.


Where is the circuit breaker located in a 1983 El Camino?

There are many circuit breakers in your 1983 El Camino. There is a circuit breaker box just below the dashboard on the far left side. The circuit breaker box should have a cover. Once the cover is removed the circuits will be revealed.