0
It is recommended to have a maximum of 8 to 10 outlets and lights combined on a 60 amp breaker depending on the power draw of the devices connected. It is important not to overload the circuit to prevent potential hazards such as electrical fires. It is advisable to consult with a qualified electrician to ensure the load on the circuit is within a safe limit.
It would be quite unusual to have a single 60 amp circuit with outlets and lights. You would have to use very heavy wire to each light and outlet. Typical lighting circuits would be protected by 15 amp breaker and a circuit with general purpose receptacles would have a 20 amp breaker. A typical lighting circuit might have 10 to 12 fixtures and receptacle circuit might have 8 outlets. If you don't know how to size a circuit get an electrician.
There is no current in a 60A circuit breaker.
The above circuit breaker is a 2 pole circuit breaker that will trip when more than 60 AMPS is being drawn through either of the 2 poles.
Add your answer:
Earn +20 pts
For a 15 amp breaker - suppose I have 8 or 12 outlets - what if on one outlet I use iron box which draws 1500 watts 12.5 amps and on another outlet a floor heater?
If there is any additional load on the outlets greater than 2.5 amps the breaker will trip. Loads of 1500 watts should be on a dedicated breaker. If the total load exceeds 15 amps the breaker will operate. However many of the outlets might supply only lights, TVs or nothing at all, so in those conditions it's OK.
Can wall outlets be on a 15amp breaker in the bedroom or do they have to be 20amp?
Wall outlets in the bedroom can be on a 15amp breaker as long as they are not part of a dedicated circuit that may have higher power demands. Typically, 15amp breakers are standard for general outlets in residential bedrooms.
If you have 3-4 can lights 1 ceiling fan and 3 outlets what size breaker?
Assuming each can light uses 1 amp, the ceiling fan uses 3 amps, and each outlet uses 2 amps, the total would be 13 amps. A 15-amp breaker would be sufficient for this setup with a little room for extra load.
How many canned lights can go on one breaker?
The number of can lights that can go on one breaker will depend on the wattage of each light and the maximum load capacity of the breaker. It's important to calculate the total wattage of all the lights and ensure it does not exceed the amp rating of the breaker to avoid overloading it. Consult with an electrician to determine the appropriate number of can lights that can safely go on one breaker.
How many recessed lights can you put on a 20 Amp circuit breaker?
As a general guideline, you can typically install about 10-12 LED recessed lights on a 20 Amp circuit breaker. However, the exact number may vary depending on the wattage of the lights and any other devices connected to the circuit. It's recommended to consult with a licensed electrician to ensure proper installation and avoid overloading the circuit.
How many electrical outlet can be install to a 30amps breaker?
A 30 amp breaker is usually used for a dedicated 30 amp device. Ordinary 15 amp receptacles can not be connected to a breaker of higher trip capacity than the rating of the receptacle. The wire size for a 30 amp breaker is #10 AWG.
How many outlets on 15 amp breaker?
As many as you want. It is the power consumed by the thing(s) plugged in that is of concern.
How many 1.2 amp lights can a 20 amp breaker hold?
No more than 13 maximum on a 20 amp circuit.
How many 115 volt outlets could you run from a 20 amp breaker?
If you never plug anything into them, there is no limit. If the total current drawn from all outlets exceeds 20 amps, the breaker will trip.
Can the power to your whirlpool be on the same 20 amp circuit as the bathroom lights and outlets?
No, the whirlpool has a motor load connected to it and should be connected to a dedicated ground fault breaker.
How many wall outlets can you have in a circuit using a A breaker?
Assuming this is not an office of a place where lots of the outlets will be used to power items that draw lots of current on a 15 amp circuit wired with 14/2 wire I would limit it to no more than 10 outlets and lights combined. On a 20 amp circuit wired with 12/2 wire I would limit it to a 14 outlets and lights combined. There is no limit in the code. You just use common sense based on what is going to be used on this circuit.
What amp breaker do you need for a run of 10 outlets?
It depends on the use of the 10 outlets. 20 amp is the norm. If this is in a shop with heavy loads then you would have to break them up.
For a 15 amp breaker - suppose I have 8 or 12 outlets - what if on one outlet I use iron box which draws 1500 watts 12.5 amps and on another outlet a floor heater?
If there is any additional load on the outlets greater than 2.5 amps the breaker will trip. Loads of 1500 watts should be on a dedicated breaker. If the total load exceeds 15 amps the breaker will operate. However many of the outlets might supply only lights, TVs or nothing at all, so in those conditions it's OK.
Can wall outlets be on a 15amp breaker in the bedroom or do they have to be 20amp?
Wall outlets in the bedroom can be on a 15amp breaker as long as they are not part of a dedicated circuit that may have higher power demands. Typically, 15amp breakers are standard for general outlets in residential bedrooms.
What kind of wire do you use for 120 volts and what amp breaker do you use?
#12/2wground & a 20 amp breaker should be enough for lights,receptales.
How many eletrcal outlets can you have in a garage?
There is no limit as to the amount of circuits you can have in a garage. If you mean how many devices on a 15 amp single circuit breaker then the answer is 12. Be sure to total in light fixture outlets and switch boxes.
Can six recessed lights of 50 watts be on a 15 amp breaker?
Should be fine if that is all that is on the breaker.
