0
What else can I help you with?
Which wire in a 240V cable with black white and bare copper wires connects to which prong in a 3-prong 30-amp 120-240V dryer outlet?
Do not use this type of cable to feed a 120/240V dryer outlet. The outlet is ungrounded, and the third conductor is neutral not ground. Your ground wire must be sheathed by code. You cannot use the bare neutral conductor as ground. Diagram Did Not Come Through. You Have a 3 Prong Connector. The Prong On The Bottom By Its Self Connect The Bare Wire. That Is What Was # 3 Connect The Others To The Two Prongs Next To Each Other. Hope This Makes Some Sense (1) (2) (3) Connect White To (1), Connect Black To (2) Bare (3) Good Luck
Originally a 240V line running from the 50A circuit to a box contaning in line fuses from this box came a 240V cable having 2 black wires and wire braid do I wire the outlet stove as a 3 or 4 prong?
Based on the description, it sounds like you should wire the stove outlet as a 3-prong outlet since the cable you have appears to have two hot wires and a ground wire (wire braid). Connect the two black wires to the hot terminals and the wire braid to the ground terminal on the stove outlet. Remember to ensure that the circuit is properly grounded for safety.
Your electric stove has a 3 prong plug your new stove has a 4 prong stove you bought a new 4 prong outlet but on your old outlet it oly has 3 wires no ground wire how do you ground it?
Look in the back of the range receptacle box that is in the wall. The three wires coming in should have a bare ground wire in the cable set. It wasn't brought to the receptacle because there was no place for it on the three wire receptacle If you find it back there under a screw terminal just add another short piece of wire under the screw and then connect the other end of the short wire to the new ground terminal on the new four position receptacle The wire should be equal in size to the size of the wire that exists around the ground terminal now. If the house is so old that the range cable did not have a ground wire in it the code allows a separate green ground #10 wire to be taken from the breaker panel box to the existing range receptacle This wire is to be bonded on each end. At the panel end to the ground buss and at the receptacle end around the ground screw at the back of the box unbroken and then to the new four position receptacle ground lug.
Need to get power from existing wall outlet to a switch?
To get power from an existing wall outlet to a switch, you will need to run a new electrical cable from the outlet to the switch location. Turn off the power to the outlet, install a new electrical box for the switch, and then connect the new cable to the outlet and the switch following the appropriate wiring diagram. Finally, install the switch into the electrical box and test to ensure it is functioning correctly.
Can you change the wall outlet to fit a 4 prong dryer outlet?
It's probably more difficult than you might expect. I'm assuming you have a NEMA 5-15R outlet, and you want to plug in a dryer that has a NEMA 14-30P plug at the end of its electric cable. The NEMA 5-15R outlet is by far the most common type of outlet in North America. It has two flat slots (hot and neutral), and a round safety ground hole. It is rated for 15 A and 125 V. On the other hand, most electric clothes dryers have an electric cable with a NEMA 14-30P plug on the end. It has two flat slots (2 hots from 2 different phases, each one 120 V from neutral, and each one rated at 30 A), an L slot (neutral), and a round safety plug. It is possible for an electrician to "fish" a electric cable carrying the necessary phases through the wall from the fuse box to that outlet, and then pull the old outlet and install a new outlet. If one merely did that last part -- pulled the old outlet and placed a new outlet -- without the proper electrical cables in the wall behind it, then the dryer would probably blow the fuse at the fusebox every time it was turned on.
How can I install an outdoor outlet in my backyard?
To install an outdoor outlet in your backyard, you will need to first turn off the power to the area where you plan to install the outlet. Next, you will need to run a weatherproof electrical cable from your home's electrical panel to the location of the outlet. Install a weatherproof electrical box at the desired location and connect the wires from the cable to the outlet. Finally, secure the outlet to the box and test it to ensure it is working properly. It is recommended to consult a licensed electrician for this installation to ensure it is done safely and up to code.
How can I install a new electrical outlet?
To install a new electrical outlet, first turn off the power to the area where you will be working. Then, determine the location for the outlet and cut a hole in the wall for the outlet box. Next, run a new electrical cable from an existing outlet or the circuit breaker box to the new outlet location. Connect the wires to the outlet following the manufacturer's instructions, and secure the outlet in the box. Finally, turn the power back on and test the outlet to ensure it is working properly.
How can I install a single circuit outlet in my home?
To install a single circuit outlet in your home, you will need to turn off the power to the area where you plan to install the outlet. Then, you will need to run a new electrical cable from the electrical panel to the location of the outlet. Next, you will need to install a new electrical box and outlet, making sure to connect the wires correctly. Finally, you will need to test the outlet to ensure it is working properly before turning the power back on. It is recommended to consult a licensed electrician for this task to ensure safety and compliance with local building codes.
What is the definition of fiber optic cable?
It's a different type of wiring inside of the cable. It makes a clearer picture and doesnt go out as often. Its normally more expensive to install though.
When should you use an ungrounded outlet?
If the wiring system into which you are installing an outlet has no ground available, use an ungrounded outlet. In an ungrounded system, an outlet with a ground contact would allow the outlet user to mistakenly, and perhaps dangerously, assume that a ground was present. A suitable ground may be available as a ground wire accompanying the hot and neutral wires in the cable, or a ground may be available via conductive conduit and a metal outlet box. In any case, use a tester to confirm the integrity of the assumed ground. A voltage test from the hot wire to the ground should show the same voltage as between hot and neutral (the black and white wires respectively). If you are replacing an ungrounded outlet, you need not assume there is no ground present. You may find, in the box, ground wires that were not connected to the outlet. You may come across grounded outlets that have no ground wire attached because they rely on grounding via the mounting screws through the outlet ears to the metal box. This is a less reliable grounding method. It is better to buy a ground-wire "pigtail," fasten the wire directly to a hole in the metal box with the supplied screw, and attach the other end of the ground wire to the outlet via the outlet's ground screw.
How can you tell if you have a 4 wire cable installed with a 3 prong outlet?
What you term as a four wire cable is known as a three wire cable in the electrical trade. The ground wire is not counted in the cable set as it is not a current carrying conductor. Turn the power off to the circuit in question. Remove the three prong outlet from the junction box. If you see a red, black, white and bare ground then you have a three wire cable feeding the receptacle. If this is what you see and the purpose of this question is to see if it can be changed to utilize a new four blade recepticle then the answer is yes.
What is the best way to connect my TV to the cable outlet using a TV coax cable?
To connect your TV to the cable outlet using a TV coax cable, simply plug one end of the coax cable into the cable outlet on the wall and the other end into the "Cable In" or "RF In" port on your TV. Make sure the TV is set to the correct input source (usually "Cable" or "Antenna") to receive the cable signal.
How can I add an electrical outlet in the middle of a run?
To add an electrical outlet in the middle of a run, you will need to cut a hole in the wall, run a new electrical cable from an existing outlet to the new location, install a new electrical box, connect the wires to the outlet, and secure the outlet in place. It is important to follow all safety guidelines and local electrical codes when doing this project.
How do you install an electric stove where a gas stove used to be?
You cap the gas pipe and run 8/3 electric cable to the location if it's fairly close. Install it in an outlet box for range plugs. If you are not familiar with electricity, hire an electrician.
What does wall charger mean?
A charger (like cable - plugs into an outlet) and charges from an outlet on the wall...?
Why would there be 9.8 volts on ground cable when tested from ground cable to battery ground?
Something is shorted to ground.
Which wire in a 240V cable with black white and bare copper wires connects to which prong in a 3-prong 30-amp 120-240V dryer outlet?
Do not use this type of cable to feed a 120/240V dryer outlet. The outlet is ungrounded, and the third conductor is neutral not ground. Your ground wire must be sheathed by code. You cannot use the bare neutral conductor as ground. Diagram Did Not Come Through. You Have a 3 Prong Connector. The Prong On The Bottom By Its Self Connect The Bare Wire. That Is What Was # 3 Connect The Others To The Two Prongs Next To Each Other. Hope This Makes Some Sense (1) (2) (3) Connect White To (1), Connect Black To (2) Bare (3) Good Luck
