0
What if there are two white wires and no black Does it make a difference which one is hooked to the black wire?
for USA, Canada and other countries running a 60 Hz supply service.
A very open-ended question!! More information is needed to give an accurate answer.
Where are these wires located? What does the black wire go to?
Assuming this is in a dwelling where NM cable (Romex) was used, I don't see how you could only have white wires.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
What else can I help you with?
How do you hook up ele plug in wires coming in to house the plug has white black and ground wires and the wire from the house has white black red and ground hooked to a 30amp fuse?
You will have to check to make sure. Normally, with 4 wires, the black and red are both power for 220. White for neutral and bare for ground. If you are only using one leg of it, you would use the black, white, bare ones and cap the red one. Someone may have used the 4 strand because they had it or 220 was planned but not done or both the red and black are hot. You should be able to tell in the panel. Do the red and black both connect to separate breakers or to one or is the red not connected?
Outside porch lamp has no box just two wires coming in black wires are tied and don't connect to fixture just the white wires what is going on here?
You would have to provide more info to be certain what your problem is. Typically a black and white wire would connect to the two wires on the light fixture. The fixture should also be controlled by a switch that "breaks" the black (Hot Wire) to turn off the fixture. If you have a volt meter you can see if there is 120Volts between the black and white wires with switch on. If there is a single white wire going to fixture (Neutral), where is the "black wires tied" to. Maybe one of the black wires has broken off the fixture.
Have a red white black wires for a dryer plug what wires are hot ones?
In a typical dryer plug, the two hot wires are usually the red and black wires. The white wire is typically the neutral wire and the green or bare wire is the ground wire. Always consult the manufacturer's instructions to be sure.
What are black with green and black with white wires mean?
Black wires are typically used for power supply, while green wires are commonly used for grounding. White wires are usually neutral wires in electrical systems. It is important to follow proper wiring color codes to ensure correct connections and safe operation of electrical devices.
Connecting black and white wires to 306 angel eyes?
Just simply, connect all the black wires to the black wire coming out of the connector, and all the white wires to the white wire coming out of the connected. Use the blocks with screw in to connect them (pick them up from most car accessories shops like halfords, wilcos....etc).
What is the difference between white and black wires in electrical circuits?
The difference between white and black wires in electrical circuits is that white wires are typically used as neutral wires, while black wires are usually used as hot wires. Neutral wires carry current back to the power source, while hot wires carry current from the power source to the device being powered.
What are the standard color codes used in house wiring for identifying the black and white wires?
In house wiring, the standard color code for identifying black wires is black, and for white wires is white.
What is the color of the wires in the electrical circuit: green, black, and white?
The color of the wires in the electrical circuit are green, black, and white.
How many wires are connected to alternator on 1966 mustang which color goes where?
There should be three wires attached to back of the alternator of a 66. You should have a black wire with a red stripe hooked to the GRD post, a black wire with a yellow stripe hooked to the BAT post and a white wire hooked to the FLD post. The black wire with the red stripe is the ground and splits off with one end bolting to the engine block on the same bolt that holds the negative battery cable to the block, the black wire with the yellow stripe goes to the hot side of the starter solenoid, and the white wire goes over to the F post on the voltage regulator.
What are the different colors of wires used in electrical circuits, including white, green, and black wires?
In electrical circuits, white wires are typically used as neutral wires, green wires are used as ground wires, and black wires are commonly used as hot wires.
What is the standard color coding for red, black, and white electrical wires in a circuit?
The standard color coding for electrical wires in a circuit is red for live or hot wires, black for neutral wires, and white for ground wires.
What is the correct order of connecting the red, black, and white wires in an electrical circuit?
The correct order for connecting the red, black, and white wires in an electrical circuit is typically red to black to white.
What are the differences between green, black, and white wires in electrical wiring?
Green wires are typically used for grounding, black wires are used for carrying electrical current, and white wires are used as neutral wires to complete the circuit.
What are the standard color codes for home wiring, specifically for identifying black and white wires?
The standard color code for home wiring is black for hot wires and white for neutral wires.
What is the correct order of connecting the red, white, black, and green wires in a circuit?
The correct order of connecting the red, white, black, and green wires in a circuit is typically red to black, white to green.
You put a new coil and not started?
Make sure the wires are hooked up the right way /red=+black= -
What are the differences between black, white, and green wires in electrical wiring?
Black wires are typically used for power supply, white wires are used for neutral connections, and green wires are used for grounding in electrical wiring.
