answersLogoWhite

0

In order to properly size the wire per National Electric Code (NEC) standards you will need to know the amperage and the distance of the device (heater) from the source (circuit breaker panel). In order to know the amperage one would need to know the voltage since amperage changes inversely with voltage.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Natural Sciences

What size of wire and breaker for a 25Kw Furnace?

For a 25 kW furnace, you typically need a 100 amp double-pole circuit breaker. The appropriate wire size would generally be 3 AWG copper or 1 AWG aluminum, depending on the length of the run and local electrical codes. Always consult with a licensed electrician to ensure compliance with local regulations and to confirm the specifications based on your specific installation conditions.


Installing a 120volt appliance what breaker is needed at the electric box?

For a 120-volt appliance, a single-pole breaker with a rating suitable for the appliance's power requirements should be installed in the electric box. The amperage rating of the breaker should match the current draw of the appliance to ensure proper protection and operation. It is important to consult with a qualified electrician to determine the appropriate breaker size for your specific appliance.


Does an electric circuit have a beaker?

No, an electric circuit does not have a beaker. A beaker is a container used for holding liquids, whereas an electric circuit consists of components like wires, batteries, resistors, and switches that allow electricity to flow in a specific path.


What is the breaker size for a 10 KVA electric heater?

The breaker size for a 10 KVA electric heater would depend on the voltage it operates at. For example, for a 240V heater, you would need a 41.67 Amp breaker (10,000 VA / 240V = 41.67 A). It is important to consult with a licensed electrician to ensure the correct breaker size and electrical setup for your specific heater.


Does an electric furnace need an outside air intake?

No, an electric furnace does not need an outside air intake. For oil and gas furnaces an air supply is needed. It is called combustion air. It is needed for complete combustion of the fuel and not use the heated air that is in the house. Today's homes are built as a sealed unit to stop infiltration air from leaking in and costing the home owner more money to heat the home. Many installations use a motorized damper that cuts off the air supply when the furnace is not operating. This prevents a draft through the vent from the outside of the house when other extracting devices are operating.

Related Questions

Why do you need a 125 amp breaker for a 83 amp furnace?

If you put a 85 amp breaker in there it will overheat from the starting and stopping of the motor. The extra size of the breaker insures that the furnace will run without interruption and without overheating the breaker. And electric motor can draw three times the amperage rated on start up momentarily. This is why there is need of extra amperage ratings.


Electric Furnace?

form_title= Electric Furnace form_header= Keep warm with an electric furnace. Do you need to replace an existing furnace?*= () Yes () No How old is your home?*= _ [50] What is the square footage of your home? *= _ [50] Will the furnace be the sole source of heating?*= () Yes () No


Fixing Your Furnace?

When the furnace in your home goes out, there are a few things that you need to look at before you get a new furnace. Get the furnace serviced by a professional electrician who will check the heating coils as well as the filter in the furnace. Check the circuit breakers in the furnace to ensure that they are working properly. If the breaker is not making contact, this could be all that you need to replace.


What should I do if my heater does not work after power outage?

I'm not sure why your furnace would shut off after a power outage but first check your breaker in the breaker box to make sure it is in the on position. If this is not the problem remove the cover on furnace and look for a red reset button on the pump. Press this button and hold for a second or two and you furnace should restart. If however it shuts down again you have other problems and will need a furnace repairman.


Where can I get a new electric furnace?

if your heater just went out in your house and you need a really good electrical furnace you should really consider getting a whole new furnace from a hardware store or a heater store.


What circuit breaker rating do you need for a 3 phase electric motor?

The circuit breaker is sized to the full load amps of the motor times 250%.


Can a 100 breaker box handle a 15 kw furnace?

The equation for amperage is I = W/E, Amps = Watts/Volts. The amperage for the furnace would be, Amps = 15000/240 = 62.5 amps. So to answer the question, yes a 100 amp breaker with a #4 copper conductor will be sufficient to operate a 15 kW furnace. A 70 amp breaker will work but it is cutting the edge a bit too fine as you don't need the furnace to trip off during the winter months (northern hemisphere) if you are away from your home for an extended period of time.


Schematics for wiring an electric heater on Goodman furnace?

I NEED WIRING DIAGRAM SHEMATIC GOODMAN Mod.PGC120225-3A


What size breaker do you need for a 40 gallon electric water heater?

Usually 30 amp


What size furnace do you need for your house?

1200 foot propane furnace what size do i need


Furnace Parts?

form_title= Furnace Parts form_header= Keep warm with a working furnace. How old is your furnace?*= _ [50] What parts do you need?*= _ [50] Please explain your issue in detail.*= _ [50]


How many watts to run a furnace?

The power needed to run a furnace can vary depending on the size and type of the furnace. However, a typical residential furnace may require anywhere from 500 to 5000 watts to operate. It's best to consult the manufacturer's specifications or a professional to determine the exact wattage requirement for your specific furnace.