0
What else can I help you with?
What wire size needed for 120 volt 3000 watt load?
AWG # 10 wire on 30 amp circuit.
What size wire needed with a 100 amp load 250 feet away?
The question is one of voltage loss. The goal is to have enough ampacity in the selected conductors to run the maximum load with only 3 percent voltage drop, caused by the resistance inherent in the wires. Plug your numbers into a voltage drop calculator online and see what pops out. At 120 volts you would get 3.1 percent drop using 3/0 wire. At 240 volts you could drop down three sizes to #1 AWG for 3.1 percent at max load, or 1/0 size for 2.5 percent drop at max load. Assuming copper wire at normal conditions of temperature.
What size wire is needed for a 180' run?
The wire size needed for a 180' run depends on the voltage, current, and type of installation. It is recommended to consult the National Electrical Code (NEC) and a professional electrician to determine the appropriate wire size to ensure safety and compliance with regulations.
What cable wire size for 1000 watts aircondition?
The only way to determine the cable wire size needed for a 1000 watt air conditioner is to find the load size. To get the load size you will need to use the formula Amps = Watts or Volts. With that being said, you will need a number 14 copper wire.
What wire size is needed for 30amp load for 34 feet on 12 volts DC?
For a 30 amp load at 12 volts DC over a distance of 34 feet, a wire size of at least AWG 8 would be recommended to minimize voltage drop and ensure efficient power delivery. It is important to consult with local electrical codes and standards to ensure compliance with regulations.
What wire size needed for 120 volt 3000 watt load?
AWG # 10 wire on 30 amp circuit.
What size wire needed with a 100 amp load 250 feet away?
The question is one of voltage loss. The goal is to have enough ampacity in the selected conductors to run the maximum load with only 3 percent voltage drop, caused by the resistance inherent in the wires. Plug your numbers into a voltage drop calculator online and see what pops out. At 120 volts you would get 3.1 percent drop using 3/0 wire. At 240 volts you could drop down three sizes to #1 AWG for 3.1 percent at max load, or 1/0 size for 2.5 percent drop at max load. Assuming copper wire at normal conditions of temperature.
What size wire is needed to operate a three quarter horsepower opener 250 ft from the breaker?
Wire size is calculated from the amount of current the load draws. More information is needed. Voltage and amperage will do fine.
What size wire is needed for a 180' run?
The wire size needed for a 180' run depends on the voltage, current, and type of installation. It is recommended to consult the National Electrical Code (NEC) and a professional electrician to determine the appropriate wire size to ensure safety and compliance with regulations.
What size wire do you need for a 208 volt 3 phase load that draws 10.5 amps?
The size of conductor needed will be a #14. It should be copper and have an insulation factor of 90 degrees C. The fact that it is a three phase load does not enter into the calculation of the wire size.
How many feet of wire to make a slinky?
The length of wire needed to make a slinky can vary depending on the size and number of coils. A standard slinky typically contains about 67 feet of wire.
What cable wire size for 1000 watts aircondition?
The only way to determine the cable wire size needed for a 1000 watt air conditioner is to find the load size. To get the load size you will need to use the formula Amps = Watts or Volts. With that being said, you will need a number 14 copper wire.
What is the type and size of cable gland or 2 core cable?
To answer this question the size of the cable or the amperage of the load is needed to calculate the correct wire size and connectors to fit the cable.
What wire size for world's simplest motor?
Wire size is based on the amperage of the load. Without knowing what the motors's full load amperage is, an answer can not be given.
What wire size is needed for 30amp load for 34 feet on 12 volts DC?
For a 30 amp load at 12 volts DC over a distance of 34 feet, a wire size of at least AWG 8 would be recommended to minimize voltage drop and ensure efficient power delivery. It is important to consult with local electrical codes and standards to ensure compliance with regulations.
What is the appropriate wire size for a 220 volt circuit with a 40 amp load?
For a 220 volt circuit with a 40 amp load, the appropriate wire size would be 8 AWG (American Wire Gauge) copper wire.
What size wire needed for 25 amps 220 volts for 75 feet?
For a 25 amp load at 220 volts over a distance of 75 feet, you will need a 10-gauge wire to ensure safe and efficient electrical conductivity. This wire size allows for minimal voltage drop and meets the necessary ampacity requirements for the circuit. Make sure to consult local electrical codes and regulations before installation.
