The wire size of three ought (000) copper with an insulation factor of 90 degrees C is rated at 210 amps.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized
IF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
For a 200 amp breaker, a minimum wire size of 2/0 gauge copper or 4/0 aluminum is typically recommended. It's important to consult local electrical codes and regulations and consider factors such as the length of the wire run and the type of insulation needed for the specific application. It is always best to consult with a licensed electrician for accurate sizing.
The breaker size for a TNIA-10 wire depends on the maximum current carrying capacity of the wire, which is typically indicated on the wire's packaging or in its specifications sheet. You should select a breaker that is rated slightly higher than the wire's maximum current capacity to ensure safety and avoid overloading the wire. It is recommended to consult with a qualified electrician for specific guidance on breaker sizing for your installation.
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
Depends on the wire size used in the circuit. If you use AWG # 14 wire you must use a 15 amp breaker. If it is wired with AWG # 12 wire then you use a 20 amp breaker. If a AWG # 10 wire is used then a 30 amp breaker is required. The breaker protects the wiring from overheating so you must use the proper size breaker for the wire used.
No, you should not run 8 gauge wire on a 50 amp breaker. The wire size should be compatible with the amperage rating of the breaker to ensure safety and prevent overheating. For a 50 amp breaker, you should use a minimum of 6 gauge wire.
A 14 gauge wire is typically used on a 15 amp circuit breaker. It is not recommended to use a larger circuit breaker with a smaller wire size as this can create a fire hazard.
50 amp breaker wired with AWG # 6 wire.
The breaker size for a TNIA-10 wire depends on the maximum current carrying capacity of the wire, which is typically indicated on the wire's packaging or in its specifications sheet. You should select a breaker that is rated slightly higher than the wire's maximum current capacity to ensure safety and avoid overloading the wire. It is recommended to consult with a qualified electrician for specific guidance on breaker sizing for your installation.
The size breaker you use is determined by the size wire used in the circuit. If you use AWG #12/2 wire then use a 20 amp breaker. If you use AWG # 14/2 then use a 15 amp breaker.
30 amp breaker with #10 gauge copper wire
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
A #10 wire has the capacity for 30 amps. No breaker larger than 30 amps should be used to protect the circuit.
Don't use aluminum wire inside the house.
25 amp breaker
Use 15 amp breaker with 14 gage wire or 20 amp breaker with 12 gage wire. Either way will work just fine.
Depends on the wire size used in the circuit. If you use AWG # 14 wire you must use a 15 amp breaker. If it is wired with AWG # 12 wire then you use a 20 amp breaker. If a AWG # 10 wire is used then a 30 amp breaker is required. The breaker protects the wiring from overheating so you must use the proper size breaker for the wire used.
Depends on how many amps it pulls and the size of the wire in the circuit.
No, you should not run 8 gauge wire on a 50 amp breaker. The wire size should be compatible with the amperage rating of the breaker to ensure safety and prevent overheating. For a 50 amp breaker, you should use a minimum of 6 gauge wire.