0
Will a breaker trip if it is being fed from the load side to energize the bus in the breaker panel?
A breaker should never be fed from its load side to energize the bus in the breaker distribution panel. This question suggests that you are trying to connect a generator to back feed your electrical panel during a power failure. This setup as killed linemen trying to repair the downed primary lines. If the panels main breaker is not opened, the generator will back feed the pole transformer that the linemen are working on and bring the line potential up to 14,000 volts. There are proper change over switches in the market now that will allow you to run your generator and the switch will automatically disconnect the utility connection before making the connection to the house panel. If this is your line of thought, do a bit of research on the subject. The last thing people in the trade want to hear is another lineman getting electrocuted.
If the load exceeds the rating of the breaker and the breaker is functioning properly, it will trip.
What else can I help you with?
How do you de-energize a circuit?
To de-energize a circuit, the voltage has to be cut off at the source. This is usually done with a disconnect switch which is located just before the circuit's load. Turning off the breaker on a distribution panel will de-energize the circuit it is feeding. To make sure that the voltage can not be turned back on when work is being done on the circuit, the switch or breaker must have a lock off device to prevent the circuit from being turned on, except by the person that locked the circuit off.
If an electrician have a circuit that pulls a load of 10 amps what size breaker must that circuit be protected by?
For a circuit with a load of 10 amps, a breaker of 15 amps should be used for adequate protection. It is important to choose a breaker size that is slightly higher than the load to prevent frequent tripping and ensure safety.
Why your electric dryer makes breaker hot?
If the circuit breaker to a dryer, or to any load, keeps getting hot and trips the breaker, then either the load is pulling too much current or there is a loose connection in the breaker or breaker panel. Either condition must be fixed to reduce the risk of fire.
How do you wire a 15 amp 120V breaker in a 240v 30 amp breaker panel?
Look to see if the 30 amp panel is fed with a two wire or a three wire. If it is a two wire then you are out of luck. If the panel is fed with a three wire then the panel should have the neutral terminated in the panel. It is this neutral that you need for 120 volt connections. You didn't state how many panel slots there are in the panel. If you are able install a 15 amp breaker into the panel and connect the wires going to the load. The black wire will go to the breaker and the white wire will go to the neutral bar in the panel.
What would happen if a 200 amp breaker is used in a 100 amp sub panel?
There are two things to think about here. First of all a 200 amp breaker will not physically fit into a 100 amp panel. This is so designed because the panel buss is not designed to conduct 200 amps before the current is cut off. A 100 amp rating on the panel is the maximum amount of current that the manufacturer states, that can be handled safely. Second if the 200 amp breaker is in the main panel then everything downstream from that breaker has to be rated for 200 amp conductivity. The wire size will have to be 3/0 from the breaker to the first over current device in the sub panel which will be the sub panel's main breaker. The sub panel can not be a load center but will have to be a combination panel. I doubt that the 100 amp sub panel's main breaker lugs would be large enough to connect the 3/0 cable.
How do you de-energize a circuit?
To de-energize a circuit, the voltage has to be cut off at the source. This is usually done with a disconnect switch which is located just before the circuit's load. Turning off the breaker on a distribution panel will de-energize the circuit it is feeding. To make sure that the voltage can not be turned back on when work is being done on the circuit, the switch or breaker must have a lock off device to prevent the circuit from being turned on, except by the person that locked the circuit off.
If an electrician have a circuit that pulls a load of 10 amps what size breaker must that circuit be protected by?
For a circuit with a load of 10 amps, a breaker of 15 amps should be used for adequate protection. It is important to choose a breaker size that is slightly higher than the load to prevent frequent tripping and ensure safety.
What happens if you energize power to wire on n.c. contacts?
If the relay contacts are in series with a connected load, then the load will energize.
Is it OK to have 250 A of breakers in a 100 A panel?
Yes. Many installations have breaker totals higher that the main breaker of the panel. It is worked on a percentage basis. Not all of the breakers will be on at the same time. In a home, on a 100 amp panel the average load is 50 - 60 amps. The 100 amp main breaker is protecting the 100 amp rated panel board. If the load current goes higher that the panel board is rated at, the main breaker will trip to protect the board.
Why your electric dryer makes breaker hot?
If the circuit breaker to a dryer, or to any load, keeps getting hot and trips the breaker, then either the load is pulling too much current or there is a loose connection in the breaker or breaker panel. Either condition must be fixed to reduce the risk of fire.
Can you load an electrical panel with only 20 amps?
If you mean can you put a single 20 amp breaker in an electric panel, the answer is yes. An electric panel is typically made to handle more breakers with values that add up to more than the rating of the panel on the supposition that you will never draw full load on all breakers. If you do the main breaker would trip. In your case you are under utilizing the panel, but this is not a problem.
Can you put a 60amp breaker and a 50amp breaker on a 60amp subpanel just as long as they are not being used at the same time?
You can. Using these size breakers in a 60 amp sub panel might be pushing the limit for breaking the sub panels feeder breaker. The breaker feeding the sub panel will have to be no bigger than 60 amps because of the main bus bar capacity of the sub panel. It would be better to install a 100 amp sub panel and then there would be a bit of a buffer and you will have the ability to add additional small load circuits.
How do you wire a 15 amp 120V breaker in a 240v 30 amp breaker panel?
Look to see if the 30 amp panel is fed with a two wire or a three wire. If it is a two wire then you are out of luck. If the panel is fed with a three wire then the panel should have the neutral terminated in the panel. It is this neutral that you need for 120 volt connections. You didn't state how many panel slots there are in the panel. If you are able install a 15 amp breaker into the panel and connect the wires going to the load. The black wire will go to the breaker and the white wire will go to the neutral bar in the panel.
What does do mean in an electrical panel schedule?
An electrical panel schedule is the index that you find on the inside of the door to the distribution panel. If the panel has no door the index is usually stuck on the face of the panel. The label has numbers on it that correspond to the breakers inside the distribution panel. A description of what the breaker feeds is written in the space next to the breaker number. Electricians usually write this description in pencil so that the description can be changed if the breaker's load is changed.
What is the conductor called that feeds current from a residential meter to the residential load center or circuit breaker panel?
Meter 'tails'.
What type of breaker do I need for my electrical panel?
You will need to determine the specific type of breaker required for your electrical panel based on the manufacturer's specifications and the electrical load requirements of your home. It is recommended to consult a licensed electrician for proper guidance and installation.
What kind of breaker would you use for a 220 hook up?
In North America a two pole breaker will be used in the distribution panel for a supply of 240 volts for a 240 volt load.
