answersLogoWhite

0

000

<<>>

A 750 MCM copper conductor with an insulation factor of 90 degrees C is rated at 500 amps.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Natural Sciences

What size wire is needed for 1600 amp service?

A 1600 amp service typically requires 500 kcmil copper wire or 750 kcmil aluminum wire. It's important to consult with a qualified electrician to determine the exact size and type of wire needed for your specific installation to ensure safety and compliance with local electrical codes.


What size wire for 200 amp service?

For a 200 amp service, it is recommended to use 3/0 copper or 4/0 aluminum wire. These wire sizes are suitable for handling the electrical load of a 200 amp service with the appropriate safety margin. It is important to consult with a qualified electrician and adhere to local electrical codes when determining the wire size for a 200 amp service.


What is the wire size needed to feed a 400 amp service with parallel copper?

It depends on the length of the run


What wire size for 70 amp service at 240 volt?

For a 70 amp service at 240 volts, you would typically use a wire size of 4 AWG copper wire. This wire size is suitable for carrying 70 amps of current safely over a 240 volt circuit. Be sure to consult local electrical codes and regulations to ensure compliance with requirements in your area.


What size ground wire should you use on a 1200 amp service?

You need to say whether it's a 150 amp service or a 1200 amp service it has to be one or the other. &lt;&lt;&gt;&gt; A 1/0 copper conductor with an insulation factor of 90 degrees C is rated at 155 amps. There is no ground wire stated for a 150 amp service so the next size up is a 200 amp service. The ground wire for this size is #6 bare AWG. Without knowing what types of loads that are coming off of the distribution a reduced neutral can not be recommended. The neutral will be the same size as the service conductor which is 1/0.

Related Questions

What is the recommended wire size for a 60 amp service?

The recommended wire size for a 60 amp service is typically 6-gauge copper wire.


What is the recommended copper wire size for a 100 amp service?

The recommended copper wire size for a 100 amp service is typically 3 AWG (American Wire Gauge).


What is the recommended wire size for a 100 amp aluminum service?

The recommended wire size for a 100 amp aluminum service is typically 2 AWG (American Wire Gauge).


What is the recommended aluminum wire size for a 200 amp service?

The recommended aluminum wire size for a 200 amp service is typically 2/0 AWG.


What size underground wire is recommended for a 200 amp service?

For a 200 amp service, it is recommended to use a size 2/0 or larger underground wire.


What is the recommended wire size for a 200 amp service using aluminum wire?

The recommended wire size for a 200 amp service using aluminum wire is typically 2/0 AWG (American Wire Gauge).


What size wire should be used for a 100 amp service in copper?

For a 100 amp service in copper, a wire size of 3/0 AWG should be used.


What size ground wire for 100a service?

A 100 amp residential service requires a size #8 copper wire, it should be insulated in green.


What information can I find in the 200 amp service wire size chart?

The 200 amp service wire size chart provides information on the recommended wire size to use for a 200 amp electrical service. This chart helps determine the appropriate wire gauge based on factors like the length of the wire run and the type of material being used.


What type of wire, specifically aluminum wire, is recommended for a 100 amp service?

For a 100 amp service, it is recommended to use aluminum wire that is at least 2 AWG in size.


What size wire should be used for a 50 amp service?

For a 50 amp service, a wire size of at least 6 AWG (American Wire Gauge) should be used to ensure safe and efficient electrical flow.


What size wire should be used for a 50 amp RV service?

For a 50 amp RV service, a wire size of 6 AWG should be used to safely handle the electrical load.