0
what is the disadvantages of pressure-tube log, acoustic- correlation log
Add your answer:
Earn +20 pts
The log of a quotient is the log of the numerator divided by the log of the denominator?
Not quite. The log(x/y) = log(x) - log(y) In words, this reads "The log of a quotient is the difference of the log of the numerator and the log of the denominator."
If log a equals x and log b equals y what is log?
"Log" is not a normal variable, it stands for the logarithm function.log (a.b)=log a+log blog(a/b)=log a-log blog (a)^n= n log a
Log x - log 6 equals log 15?
log(x) - log(6) = log(15)Add log(6) to each side:log(x) = log(15) + log(6) = log(15 times 6)x = 15 times 6x = 90
Is log 5 equivalent to log 5-log 20?
No. log 20 is a positive number , so it you subtract it from log 5 you get less than log 5. However, log10 5 = 1 - log102 = 2- log1020 . or log 5 - log 20 = log 5 - log 4*5 = log 5 - (log 5 + log 4) = log 5 - log 5 - log 4 = - log 4 But we do not need to do all of these computations, because log 5 is different from log 5 - log 20 by the law of the equality that says two equals remain equal if and only if we subtract (in our case) the same thing from them.
How do you solve for a power in a math problem?
You have to use logarithms (logs).Here are a few handy tools:If [ C = D ], then [ log(C) = log(D) ]log(AB) = log(A) + log(B)log(A/B) = log(A) - log(B)log(Np) = p times log(N)
State the basic principle of the pressure tube log?
The basic principle of the pressure tube log is to measure the pressure difference between two points along a tube to calculate fluid flow rate. By measuring the pressure at these points and knowing the fluid characteristics, the flow rate can be determined using a formula based on Bernoulli's principle.
How a dropping tube uses air pressure?
A dropping tube uses air pressure by creating a pressure difference between the inside and outside of the tube. When the tube is sealed at the top and the bottom is opened, the pressure inside the tube decreases as the air escapes, causing the liquid to be "dropped" into a container below.
How do you make a simple hydraulic?
Take a tube, put a piston in it, seal off both ends of the tube, and use a liquid, or gas to put pressure in and remove pressure from the tube. As the fluid or gas goes in the tube, the pressure pushes the piston out. As the pressure is released, the piston can recede.
A Bourdon tube is often found in a?
A bourdon tube is a type of curved tube where the inside radius is smaller than the outside radius. As Force = Pressure x Area this means that when a pressure is applied internally to the tube the greater surface area on the outside causes the tube to straighten out. This is connected via a mechanical linkage to dial on the front of the gauge. Your typical industrial pressure gauge is the Bourdon Tube tyep.
What turbine does not require draft tube?
Draft tube is used to increase the pressure from the low turbine exit pressure to the pressure of the surrounding to which the fluid is rejected.Only reaction turbines require a draft tube as there is low pressure at the exit of the turbine,where as in an impulse turbine the pressure at the inlet and the exit is essentially the same, which is above the pressure to which the fluid is rejected and thus it require no draft tube.
Where is the low pressure air conditioner port on a 2001 Chrysler town and country?
There are two aluminum tubes coming out of the compressor. The high pressure tube goes to the condensor in front of the radiator. The low pressure tube is the other tube, and the port has a black plastic cap over it, on the low pressure tube.
What is principal of bourdon tube?
The bourdon tube is a curved oval cross-sectional tube. The tendency of a fluid under pressure to try to shape its container, the tube, into a spherical shape causes the tube to elongate, moving the dial mechanism to a position indicating the application of pressure. The greater the pressure applied the greater the movement of the tube.
What happens when you blow over the mouth of a test tube which is half filled with water?
Blowing over the mouth of the test tube will create a decrease in air pressure inside the tube. This decrease in pressure will cause the water in the test tube to rise up due to the higher pressure outside the tube. Ultimately, the water level in the test tube will rise as a result of the change in pressure.
Why pressure is low in fire tube boilers?
Hot pressure
Pressure inside a bourdon tube pressure gadge causes the bourdon to straighten or curl?
It causes the Bourdon tube to straighten.
What are the types of boiler?
fire tube & water tube . high pressure and low pressure. low capacity and high capacity.
What is the use of Bourden tube pressure gauge?
A Bourdon tube pressure gauge is used to measure the pressure of a gas or liquid in a system. When the pressure increases, the tube straightens, and this movement is indicated on the gauge's dial. Bourdon tube gauges are commonly used in various industries to monitor and regulate pressure in systems to ensure safe and efficient operation.
