0
What else can I help you with?
What size of breaker to use on a wall unit 220 heater?
The size of the breaker needed for a 220V wall heater depends on the current rating of the heater. Generally, for a 220V heater, a 20-amp breaker is common. However, it's important to check the manufacturer's specifications and local electrical codes for the appropriate breaker size.
What local contractors provide heater installation service?
A licensed electrician can install a heater for you. I would look in your local yellow pages for a licensed electrician to install the heater and any other electrical work you may have.
What is the appropriate water heater breaker size according to the water heater breaker size chart?
The appropriate water heater breaker size is determined by the water heater's wattage and voltage, as indicated in the water heater breaker size chart. It is important to match the breaker size to the specifications of the water heater to ensure safe and efficient operation.
Can you use a vacuum breaker on a hot water heater to keep from emptying it when draining house pipes in winter?
Yes install it on the cold water line as close to the heater as possible.
What size circuit breaker for 240v 60hz garage heater?
The size of the circuit breaker for a 240V, 60Hz garage heater typically depends on the heater's wattage. A common rule of thumb is to choose a breaker rated at 125% of the heater's full load current. For example, if the heater is rated at 4,000 watts, the current draw would be approximately 16.7 amps, so a 20-amp circuit breaker would be appropriate. Always consult the manufacturer's specifications and local electrical codes for precise requirements.
Why would the breaker to your hot water heater keep kicking off?
You have a major electrical problem.. If a breaker trips more than once you need to leave it off and call an electrican.
What is the breaker size for a 10 KVA electric heater?
The breaker size for a 10 KVA electric heater would depend on the voltage it operates at. For example, for a 240V heater, you would need a 41.67 Amp breaker (10,000 VA / 240V = 41.67 A). It is important to consult with a licensed electrician to ensure the correct breaker size and electrical setup for your specific heater.
Why does your circuit braker shut off when you turn on your heater?
Your circuit breaker shuts off when you turn on your heater because the heater draws a significant amount of electrical current, potentially exceeding the circuit's capacity. This overload causes the breaker to trip as a safety measure, preventing overheating and potential fire hazards. Additionally, if there are any underlying electrical issues or faulty wiring, this could also contribute to the breaker tripping. It's advisable to consult an electrician to assess the situation.
Is the blower to the heater and air conditioner fun by a fuse?
Yes, the blower for both the heater and air conditioner is typically powered through a fuse or circuit breaker within the electrical system of the HVAC unit. If the blower is not functioning, checking the fuse or breaker is a common troubleshooting step. A blown fuse or tripped breaker may indicate an electrical issue or overload that needs to be addressed. Always ensure safety by turning off power before inspecting electrical components.
Where to Install a New Water Softener?
When selecting the ideal location for installing a new water softener, it is best to install it near the water heater in your home that you will find the easiest place to tie the new unit into the existing plumbing system. The ideal location, near the water heater is typically in the utility room, garage, or basement of your home. Remember that your water softening system will also need to be within easy access range of both an electrical receptacle capable of handing the manufacturer specified amperage, and a utility sink or floor drain.
How to install a wall heater?
To install a wall heater, first choose a suitable location on the wall. Make sure there is proper clearance around the heater. Next, mount the heater on the wall using the provided hardware. Connect the heater to the electrical supply following the manufacturer's instructions. Finally, test the heater to ensure it is working properly and safely.
Where can one purchase a utility heater?
One can purchase a utility heater from many general hardware stores, such as B&Q. Alternatively, one can buy a utility heater from webpage stores such as Amazon or Ebay.
